Mohammad Reza Ghorbani Fard

Mr. Mohammad Reza Ghorbani Fard

Department of Nanometrology and Nanomaterials, Moscow Institute of Physics and Technology, Dolgoprudnyy, Moskovskaya Oblast’, Russia
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 November 2020 in The European Physical Journal Plus
Verified
Journal Article
Closed access
PDF file
FBForough Bozorgzadeh
Forough Bozorgzadeh
MFMohammad Reza Ghorbani Fard
Mohammad Reza Ghorbani Fard
MSMostafa Sahrai
Mostafa Sahrai

1 January 2024 in International Journal of Engineering
Verified
Journal Article
Open access
PDF file
AEAlexey Efimov
Alexey Efimov
APA. Patarashvili
A. Patarashvili
DKDenis Kornyushin
Denis Kornyushin
MIM. Ivanov
M. Ivanov
ALAnna Lizunova
Anna Lizunova
VIV. Ivanov
V. Ivanov
Aerosol particle charging is widely used in various technical applications. A model of a needle-plate type charger for efficient charging of aerosol nanoparticles in a corona plasma discharge has been developed and investigated. The main difference from similar devices in the modernization of the grounded plate hole's geometry and the number of corona needles exist. This has resulted in a substantial increase in the charger's efficiency by over 25%. The effects of two types of discharge plates, one with cylindrical and the other with conical inner holes, on the extrinsic charging efficiency of aerosol particles were experimentally investigated. Metallic nanoparticles of Ag with sizes ranging from 20 to 160 nm and a number concentration of 106 to 108 cm-3 were utilized as the test aerosol. This system shows that the maximum efficiency of particle charging is attained by using a plate with a conical hole, which reduces electrostatic losses from 37±3% to 20±2%. Furthermore, an additional effect of increasing the particle charging efficiency was also observed by using a multi-pointed needle, which resulted in lower electrostatic losses compared to a single needle. Experimental evidence confirms that utilizing a conical hole in the plate and a multi-pointed needle has increased the particle charging efficiency from 47±3% to 59±4%, as opposed to the standard design featuring a cylindrical hole and a single-pointed needle. In this paper, an increase in the efficiency of charging particles in a charger with a multi-pointed needle compared to a single-pointed one is shown for the first time.

1 January 2025 in International Journal of Engineering
Verified
Journal Article
Open access
PDF file
APAnton Patarashvili
Anton Patarashvili
MFMohammad Reza Ghorbani Fard
Mohammad Reza Ghorbani Fard
MIM. Ivanov
M. Ivanov
OVO. Vershinina
O. Vershinina
DLD. Labutov
D. Labutov
VIV. Ivanov
V. Ivanov
This article presents the development of a multielectrode spark discharge generator designed to produce multicomponent nanoparticles with precise control over the elemental ratios. This capability is achieved through the creation of two independent spark discharges positioned extremely close to one another, facilitating improved mixing of materials. Both theoretical and experimental studies demonstrate that this new generator exhibits similarities with its predecessor, which simplifies the integration process. The EDX analysis clearly demonstrated the capability to systematically control the atomic fraction of aluminum in combinations of tungsten, copper, and aluminum. This proportion varied from 22% to 2% in nanoparticles, which had an average mobility diameter of 27 nm. These nanoparticles were composed of atomic clusters of the respective materials with an average size of 2 nm. Also, using two independent discharges the elemental composition of two-component nanoparticles can be precisely adjusted over the entire range by using two electrodes made of the same material. Additionally, HR-TEM coupled with SAED analysis revealed a high degree of amorphousness in the nanoparticles, indicating effective mixing of the components. These findings pave the way for the development of multicomponent nanoparticles with tailored properties, holding significant potential for a wide array of scientific and technological applications.

15 December 2024 in Journal of Aerosol Science
Verified
Journal Article
Closed access
APAnton Patarashvili
Anton Patarashvili
MFMohammad Reza Ghorbani Fard
Mohammad Reza Ghorbani Fard
AEAlexey Efimov
Alexey Efimov
MIMatthew Ivanov
Matthew Ivanov
EKEkaterina Kameneva
Ekaterina Kameneva
VIVictor Ivanov
Victor Ivanov

14 October 2021
Verified
Conference Paper
Closed access
HPHojatollah Poudineh
Hojatollah Poudineh
MFMohammad Reza Ghorbani Fard
Mohammad Reza Ghorbani Fard
In this work, a dual-junction InGaP/SiGe solar cell system with two graded buffer regions Si 0.18 Ge 0.82 is proposed. The focus is on the effect of optimizing the SiGe Base layer. The Silvaco ATLAS device simulator is used to simulate 1 sun illumination under standard AM1.5G spectrum. Also, various performance parameters such as open-circuit voltage, short-circuit current density, Efficiency, and Fill Factor are analyzed and compared with the published results from recent literature. For the proposed structure, the following parameters are obtained for the base layer Si 0.18 Ge 0.82 : I sh = 20.2995 mA/cm2, V oc = 2.0574 V, η= 36.54 % and FF = 87.55 %.

2 February 2024 in Preprints.org
Verified
Preprint
Open access
PDF file
AEAlexey Efimov
Alexey Efimov
APAnton Patarashvili
Anton Patarashvili
DKDenis Kornyushin
Denis Kornyushin
MIMatthew Ivanov
Matthew Ivanov
ALAnna Lizunova
Anna Lizunova
VIVictor Ivanov
Victor Ivanov
Aerosol particle charging is widely used in various technical applications. A model of a needle-plate type charger for efficient charging of aerosol nanoparticles in a corona plasma discharge has been developed and investigated. The main difference from analogues is the modernization of the geometry of the hole in the grounded plate and the number of corona needles. This led to a significant increase in the efficiency of the charger by more than 25%. The effect of two types of discharge plates with cylindrical and conical inner holes on the external charging efficiency of aerosol particles is experimentally investigated. Metallic nanoparticles of Ag with sizes of 20–160 nm and number concentration of 106–108 cm−3 were used as a test aerosol. It is found that the maximum efficiency of particle charging is achieved by using a plate with a conical hole by reducing electrostatic losses from 37±3% to 20±2%. This is due to the redistribution of the electrostatic field strength lines when changing the cylindrical hole to a conical one. An additional effect of increasing the efficiency of particle charging was also achieved through the use of a multi-pointed needle, which provided lower electrostatic losses compared to a single needle at the same corona discharge current of 20 µA. It has been experimentally shown that the use of a conical hole of the plate and a multi-pointed needle increased the charging efficiency of particles from 47±3% to 59±4% in comparison with the standard design with a cylindrical hole and a single-pointed needle.