Mohd Mustafa Al Bakri Abdullah

Prof. Dr. Mohd Mustafa Al Bakri Abdullah

Universiti Malaysia Perlis

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2016 in Progress in Materials Science
Verified
Journal Article
Closed access
YLYun-Ming Liew
Yun-Ming Liew
CHCheng Yong Heah
Cheng Yong Heah
Mohd Mustafa Al Bakri AbdullahMohd Mustafa Al Bakri Abdullah
Mohd Mustafa Al Bakri Abdullah
HKHussin Kamarudin
Hussin Kamarudin

1 January 2014 in Construction and Building Materials
Verified
Journal Article
Closed access
OAOmar Abdulkareem
Omar Abdulkareem
Mohd Mustafa Al Bakri AbdullahMohd Mustafa Al Bakri Abdullah
Mohd Mustafa Al Bakri Abdullah
HKH. Kamarudin
H. Kamarudin
INI. Khairul Nizar
I. Khairul Nizar
ASAla’eDdin A. Saif
Ala’eDdin A. Saif

1 October 2012 in Construction and Building Materials
Verified
Journal Article
Closed access
CHCheng Yong Heah
Cheng Yong Heah
HKH. Kamarudin
H. Kamarudin
Mohd Mustafa Al Bakri AbdullahMohd Mustafa Al Bakri Abdullah
Mohd Mustafa Al Bakri Abdullah
MBM. Bnhussain
M. Bnhussain
MLM. Luqman
M. Luqman
YLYun Ming Liew
Yun Ming Liew

Verified
Journal Article
Open access
PDF file
Mohd Mustafa Al Bakri AbdullahMohd Mustafa Al Bakri Abdullah
Mohd Mustafa Al Bakri Abdullah
KHKamarudin Hussin
Kamarudin Hussin
MBMohammed Binhussain
Mohammed Binhussain
KIKhairul Nizar Ismail
Khairul Nizar Ismail
ZYZarina Yahya
Zarina Yahya
RRRafiza Abdul Razak
Rafiza Abdul Razak
In this paper, we report the results of our investigation on the possibility of producing foam concrete by using a geopolymer system. Class C fly ash was mixed with an alkaline activator solution (a mixture of sodium silicate and NaOH), and foam was added to the geopolymeric mixture to produce lightweight concrete. The NaOH solution was prepared by dilute NaOH pellets with distilled water. The reactives were mixed to produce a homogeneous mixture, which was placed into a 50 mm mold and cured at two different curing temperatures (60 °C and room temperature), for 24 hours. After the curing process, the strengths of the samples were tested on days 1, 7, and 28. The water absorption, porosity, chemical composition, microstructure, XRD and FTIR analyses were studied. The results showed that the sample which was cured at 60 °C (LW2) produced the maximum compressive strength for all tests, (11.03 MPa, 17.59 MPa, and 18.19 MPa) for days 1, 7, and 28, respectively. Also, the water absorption and porosity of LW2 were reduced by 6.78% and 1.22% after 28 days, respectively. The SEM showed that the LW2 sample had a denser matrix than LW1. This was because LW2 was heat cured, which caused the geopolymerization rate to increase, producing a denser matrix. However for LW1, microcracks were present on the surface, which reduced the compressive strength and increased water absorption and porosity.

1 June 2019 in Construction and Building Materials
Verified
Journal Article
Closed access
ABAissa Bouaissi
Aissa Bouaissi
LLLong-Yuan Li
Long-Yuan Li
Mohd Mustafa Al Bakri AbdullahMohd Mustafa Al Bakri Abdullah
Mohd Mustafa Al Bakri Abdullah
Quoc-Bao BuiQuoc-Bao Bui
Quoc-Bao Bui

1 January 2011 in Physics Procedia
Verified
Journal Article
Open access
CHCheng Yong Heah
Cheng Yong Heah
HKH. Kamarudin
H. Kamarudin
Mohd Mustafa Al Bakri AbdullahMohd Mustafa Al Bakri Abdullah
Mohd Mustafa Al Bakri Abdullah
MBMohammed Binhussain
Mohammed Binhussain
MLM. Luqman
M. Luqman
YLYun Ming Liew
Yun Ming Liew
Depending on the processing conditions, geopolymers can exhibit a wide variety of properties and characteristics. Curing profile serves as a crucial parameter in synthesis of geopolymers. In this paper, the influence of curing temperature and curing time on the properties of kaolin-based geopolymer was studied. The samples were separated into several curing conditions; including curing at ambient temperature, 40°C, 60°C, 80°C and 100°C for 1 day, and up to 3 days. The compressive strength and SEM analysis of geopolymer products were evaluated. Results showed that curing condition has a significant effect on the mechanical properties of kaolin-based geopolymer. Generally, curing at ambient temperature was not feasible, while increase in temperature favored the strength development. In addition, prolonged curing time improved the geopolymerization process, and led to higher strength gain. However, curing at high temperature for a long period of time caused failure of the sample at a later age