We investigated the reinforcement behavior of small amounts of chemically unmodified cellulose nanofiber (CNF) in eco-friendly natural rubber (NR) nanocomposites. For this purpose, NR nanocomposites filled with 1, 3, and 5 parts per hundred rubber (phr) of cellulose nanofiber (CNF) were prepared by a latex mixing method. By using TEM, a tensile test, DMA, WAXD, a bound rubber test, and gel content measurements, the effect of CNF concentration on the structure–property relationship and reinforcing mechanism of the CNF/NR nanocomposite was revealed. Increasing the content of CNF resulted in decreased dispersibility of the nanofiber in the NR matrix. It was found that the stress upturn in the stress–strain curves was remarkably enhanced when the NR was combined with 1–3 phr CNF, and a noticeable increase in tensile strength (an approximately 122% increase in tensile strength over that of NR) was observed without sacrificing the flexibility of the NR in the NR filled with 1 phr CNF, though no acceleration in their strain-induced crystallization was observed. Since the NR chains were not inserted in the uniformly dispersed CNF bundles, the reinforcement behavior by the small content of CNF might be attributed to the shear stress transfer at the CNF/NR interface through the interfacial interaction (i.e., physical entanglement) between the nano-dispersed CNFs and the NR chains. However, at a higher CNF filling content (5 phr), the CNFs formed micron-sized aggregates in the NR matrix, which significantly induced the local stress concentration and promoted strain-induced crystallization, causing a substantially increased modulus but reduced the strain at the rupture of the NR.
This work investigates the effect of epoxidized low molecular weight natural rubber (ELMWNR) in silica- and carbon black-filled natural rubber (NR) compounds on processing and mechanical and dynamic mechanical properties. The ELMWNRs with different mol% epoxide content were prepared from depolymerization of epoxidized NR using periodic acid in latex state to have a molecular weight in a range of 50 000–60 000 g/mol. Their chemical structures and actual mol% of epoxide were analyzed by 1H NMR. The ELMWNRs were added to the filled NR compounds as compatibilizers at varying loadings from 0 to 15 phr. The addition of ELMWNR decreases compound viscosity and the Payne effect, that is, filler–filler interaction, of the silica-filled compound. In the silica–silane compound and the compound with 28 mol% epoxide (ELMWNR-28), the compound viscosities are comparable. The optimal mechanical properties of silica-filled vulcanizates are obtained at the ELMWNR-28 loading of 10 phr. In contrast, the addition of ELMWNR to a carbon black-filled compound shows only a plasticizing effect. The incorporation of ELMWNR into NR compounds introduces a second glass transition temperature and affects their dynamic mechanical properties. Higher epoxide contents lead to higher loss tangent values of the rubber vulcanizates in the range of the normal service temperature of a tire.
26 November 2015 in Journal of Applied Polymer Science
Natural rubber (NR) nanocomposites reinforced with five parts per hundred rubber (phr) of two different nano-fillers, i.e., nanoclay (abbrev. NC) and cellulose nanofiber (abbrev. CNF), were prepared by using latex mixing approach, followed by mill-compounding and molding. The morphology, stress–strain behavior, strain-induced crystallization, and bound rubber of the NR nanocomposites were systematically compared through TEM, tensile test, WAXS, DMA, and bound rubber measurement. The aggregated CNFs were observed in the NR matrix, while the dispersed nanosized clay tactoids were detected across the NR phase. The reinforcement effects of NC and CNF were clearly distinct in the NR nanocomposites. At the same nano-filler content, the addition of NC and CNF effectively accelerated strain-induced crystallization of NR. The high tensile strength obtained in the NC-filled NR nanocomposite was attributed to strain-induced crystallization of NR accelerated by well-dispersed NC. However, the larger tensile modulus and low strain for the CNF-filled NR were related to the formation of immobilized NR at the interface between CNF aggregate and NR. The immobilization effect of NR at the CNF surface offered by a mutual entanglement of CNF aggregate and NR chain led to local stress concentration and accelerated strain-induced crystallization of CNF/NR nanocomposite. From the present study, the NR nanocomposites combined with 5 phr CNF shows high-tensile modulus and acceptable breaking tensile stress and strain, suggesting the application of CNF/NR based nanocomposite in automotive and stretchable sensors for next-generation electronic devices.