Functionalized carbon-based materials have recently attracted attention for the efficient removal of complex pollutants, including dyes. In this study, agave bagasse, an abundant by-product of the Mexican tequila industry, was used as biomass to produce H2SO4-modified hydrochar (HC) for the removal of Reactive Orange 84 (RO84). FTIR-ATR analysis revealed characteristic signals of –SO3H groups in the functionalized HC. BET characterization showed a broad range of surface areas and pore volumes, with pore radio indicating nano-, micro-, and mesoporous structures, depending on the acid concentration used during synthesis. TGA and XRD analyses indicated that higher acid concentration promoted the depolymerization of biomass components. Adsorption assays demonstrated that increasing H2SO4 concentrations enhanced dye removal. Post-adsorption FTIR-ATR analysis revealed signal shifts consistent with interactions between sulfonated groups and dye RO84. Statistical and mathematical analyses showed that optimal results were achieved by combining high acid concentrations during HC synthesis with high HC dosages during adsorption.
Hydrothermal carbonization (HTC) of agricultural waste is a promising waste management technique. However, the use of different raw materials may produce hydrochars with varying efficiencies, both in yield and application, and environmental impacts, due to differences in composition and required processing conditions. To understand the influence of biomass type and acid-assisted HTC conditions, this study used sugarcane and agave bagasse to produce functionalized hydrochars and evaluated them for the removal of Reactive Orange 84; an azo dye used in the textile industry. Material characterization was performed using FT-IR, TGA, BET, and XRD analyses. In addition, a life cycle assessment was conducted to evaluate environmental impacts associated with hydrochars produced using H2SO4 at concentrations of 0.2 and 0.5 M. TGA and XRD results indicate that agave bagasse hydrochars (HBA) retain more crystalline lignocellulosic structures, whereas sugarcane bagasse hydrochars (HBS) exhibit predominantly amorphous structures after HTC. FT-IR analysis confirmed the presence of –SO3H functional groups; however, HBA samples showed greater availability of these groups with increasing acid concentration. Adsorption experiments and LCA results demonstrated that the most favorable treatment, in terms of emission reduction and dye removal, was agave bagasse functionalized with 0.5 M H2SO4, achieving 75.7% mass yield and 94.5% dye removal.
Biogenic nanoparticles have recently emerged as promising bacterial growth inhibitors, requiring low concentrations and not producing harmful byproducts. However, knowledge gaps remain regarding how different extraction techniques affect nanoparticle synthesis, thereby influencing their replicability and scalability across various applications. To address these knowledge gaps, this study compared six extracts derived from Moringa oleifera biomass for the synthesis of iron oxide nanoparticles. Multivariate statistical analyses correlated extraction methods with biomolecule content (polyphenols, flavonoids, carbohydrates, proteins), iron percentage, and E. coli growth inhibition. All extracts showed varying concentrations of biomolecules, and different extraction methods were preferable for specific components. Flavonoids were best extracted by salting-out, while infusion methods were better for obtaining carbohydrates. Higher percentages of iron (22.77%) were linked to the presence of polyphenols and flavonoids. Nanoparticles prepared using salting-out and infusion extraction from leaf biomass displayed the highest efficiency in inhibiting E. coli growth, up to a dilution factor of 4. The outcomes of this research study provide an in-depth understanding of the role of specific biomolecules in biogenic nanoparticle synthesis, confirming that both synthesis yield and application effectiveness depend on the extract preparation method.
This study focused on the generation and characterization of sludge produced by electrocoagulation (EC) combined with Moringa oleifera seed extract (MOSE) to remove water hardness. First, an experimental data set was generated and used as the baseline data for mathematical modeling to identify the effects of different parameters on Ca2+ and Mg2+ ion hardness removal. Then, using the generated data set, operational conditions were optimized using neural networks integrated with a genetic algorithm, resulting in the selection of Fe electrodes, 12.5 mL of MOSE per 100 mL of water, a current density (j) of 49.16 mA cm−2, and a reaction time of 5.3 min, considering Ca2+ ions as the sample contaminant. Additionally, machine learning analysis identified contaminant type, reaction time, and cathode material as the most influential variables affecting sludge formation, with optimal conditions identified for both Ca2+ and Mg2+ ion systems. For all the mathematical models, experimental validation was performed. The MOSE extract was characterized for the presence of proteins, polyphenols, flavonoids, and polysaccharides, which provide functional groups that promote aggregation and floc development. Sludge characterization by FT-IR, TGA, and TEM revealed the formation of organic–inorganic hybrid matrices composed of biomolecules interacting with electrochemically generated Fe3+ and Al3+ species, as well as Ca2+ and Mg2+ ions. These results highlight the role of plant-derived biomolecules in modulating the sludge structure and composition, providing insight into the mechanisms of sludge formation and the implications for handling and valorization of EC-based water treatment systems.