The negative-ion based neutral beam injector for heating and current drive of the ITER plasma (ITER HNB) is under development, at present focusing on the optimization of the full-scale plasma source in the SPIDER test stand. The production of H⁻ or D⁻ ions in the ion source is based on the low work function surfaces obtained by caesium evaporation. This paper describes the caesium conditioning procedure and the corresponding beam performances during the first operation of SPIDER with caesium. Technical solutions to overcome present limitations of the test stand are described. The influence of source parameters on the caesium effectiveness was investigated in short beam pulse operation; with total radio-frequency (RF) power of 400 kW and filling pressure below 0.4 Pa, and a limited number of extraction apertures, a negative ion current density of about 200 A m⁻² was extracted in hydrogen, with beam energy lower than 60 keV. Beam optics and beam uniformity were assessed thanks to the acceleration of isolated ion beamlets. A possible procedure to accelerate a uniform beam was demonstrated at low RF power. The results obtained in this first investigation provided key indications on the operation of one of the largest existing sources of accelerated negative hydrogen-like ions.

An overview of the recent operations and the main results of cesium injection in the Source for the Production of Ions of Deuterium Extracted from Rf plasma (SPIDER) negative ion source are described in this contribution. In experiments without cesium injection, all SPIDER plants were tested to verify the basic expectations on the operational parameters (e.g., electron cooling effectiveness of magnetic filter field) and to determine its operational region. For beam properties, it was shown that the current density varies across the beam in the vertical direction. In preliminary cesium experiments, the expected increase of negative ion current and simultaneous decrease of co-extracted electrons were found, along with the influence of the control parameters (polarization of the plasma electrodes, magnetic filter field) on the SPIDER beam uniformity in the horizontal and vertical directions. It was shown that non-Gaussian tails can be identified in the angular distribution on the plane perpendicular to the beam propagation direction. Stray particles, nonhomogeneous beam and large divergence might result in unexpected heat and particle loads over ITER neutral beam injector (NBI) accelerator grids; it is the goal of SPIDER to assess and possibly to identify suitable methods for controlling these beam features. A major shutdown, planned for late 2021, to solve the issues identified during the operation and to carry out scheduled modifications, is outlined. Such improvements are expected to allow SPIDER to pursue the ITER requirements in terms of negative ion current, electron-to-ion ratio, and beam duration.

HV insulation across a single gap in vacuum and low-pressure gas is a critical issue in relation to the development and realization of the electrostatic accelerator for the ITER Neutral Beam Injector (NBI) [1]. The present paper describes and analyzes the recent experimental results obtained at the High Voltage Padova Test Facility (HVPTF), the laboratory aimed at supporting the development of the prototype for the ITER NBI [2]. A voltage up to 800kVDC was achieved in the HVPTF during the experimental campaigns with a sphere-plane configurations having variable gap length (from 30 to 150 mm) and pressure ranging from high vacuum (10-7 mbar) to 10-3 mbar in Argon. Such an experimental campaign represents one of the few examples where voltages higher than 500-550 kV DC are sustained by a single vacuum gap between electrodes [3] and therefore constitutes additional experience to improve the knowledge of voltage holding across large vacuum gaps. The results in high vacuum indicate that at the beginning of voltage conditioning the breakdown events occur at the same cathodic electric field irrespective of the electrode geometry. However, after sufficient conditioning time, the breakdown voltage distribution seems to depend also on the electric field at the anode and on the total voltage between electrodes. A benchmark between a numerical tool previously developed to predict the voltage holding in high vacuum (Voltage holding Prediction Model, VHPM [4]) and the experimental results is also reported and discussed.

In the framework of the program for the construction of 1 MeV-16 MW negative neutral beam injector (NNBI) for ITER, a research and development activity on voltage holding in vacuum has been initiated since 2009, aimed at supporting the design, construction, and development of the NNBI accelerator. For this purpose, the voltage holding prediction model (VHPM) previously developed has been updated. In the VHPM, the effect of the anodic electric field and the cathodic electric field on the probability of breakdown is evaluated by means of two exponents: α and y. On the basis of the experimental results from different test stands and of detailed 3-D numerical simulation of the corresponding electric-field configurations, the predictions of the VHPM numerical code have been benchmarked. New exponents, α and y, have been proposed to obtain a more precise location of the weak point of the system and a better prediction of the maximum withstanding dc voltage in high vacuum.

The Divertor Tokamak Test facility (DTT) will be a new experimental facility located at Frascati, Rome, Italy, whose main goal will be to have a better understanding on hot plasma interactions with plasma-facing components (PFCs) and aid in the development of ITER and successively DEMO. The improved conceptual design of the beamline for the DTT neutral beam heating (NBH) system is here overviewed, with a particular focus on the technical solutions adopted to fulfill the requirements and maximize beamline performances. The proposed system features a beamline providing deuterium neutrals (D⁰) with an energy of 510 keV and an injected power of 10 MW. Various design options have been considered, and a comprehensive set of simulations has been carried out using several physics and engineering codes to drive the choice of the most suitable design options and optimize them, aiming at finding a good compromise among different design requirements.

Localized heating has been observed in unexpected positions on anodic surfaces in a multi-electrode device insulated by vacuum gaps. In double polarity experiments, a counter-intuitive behavior of current-voltage characteristic has also been observed. The phenomena could depend on a cascade effect of charged particles exchanged between electrodes and on a mutual correlation of particle trajectories between electrode surfaces occurring during the high voltage conditioning phase. Attractors regions ascribed to regenerative processes of charged particles between cathode and anode have been identified thanks to numerical simulations The position of the attractors depends only on electrode shape and the ratios of applied voltages. This finding suggests new perspectives in neutrons sources applications, where recurrent impacts of focused high energy hydrogen isotopes take place on solid hydride targets supported by metallic electrodes insulated by vacuum gaps