The increase in positioning accuracy and repeatability allowed the integration of robots in assembly operations using guidance systems (structured applications) or video acquisition systems (unstructured applications). This paper proposes a procedure to determine the measuring plane using a 3D laser camera. To validate the procedure, the camera coordinates and orientation will be verified using robot coordinates. This procedure is an essential element for camera calibration and consists of developing a mathematical model using the least square method and planar regression. The mathematical model is considered necessary as a step towards optimizing the integration of robotic vision systems in assembly applications. A better calibrated camera has the potential to provide better recognition results, which are essential in this field. These improved results can then be used to increase the accuracy and repeatability of the robot.
Free form fabrication (FFF), also known as fused deposition modeling (FDM), is a widespread and accessible method for prototyping. Parts a with lattice structure having functional roles as mechanism elements is becoming more common. In the research field, the mechanical characteristics as well as optimization methods for manufacturing these parts are major points of interest. One of the major aspects of FFF is part orientation during print, as it has influence over a wide range of variables, from tensile strength to surface quality and material consumption. For parts with a lattice structure, the printing orientation is important not only as a factor that influences the characteristics of the part itself, but also as a factor that determines the support requirements. However, due to the complex lattice structure, removing supports from these parts can be a challenging task. This study focuses on analyzing the reliability of available CAD optimization methods for FFF pre-processing. The analysis is performed using the Design for Additive Manufacturing module included in the Siemens NX software, version NX2406. The efficiency of CAD optimization was observed by taking into account the material consumption, printing times, surface quality, and support requirements. The study methods were based on the comparative analysis approach. The case studies used for the comparative analysis consider two-part inner structures: the solid structure approach with a rectilinear infill and the lattice structure approach.
This research investigates the optimization of operational efficiency and cost reduction through the enhancement of material flow management within production line stations. Departing from conventional static analyses, the study employs advanced simulation tools to pinpoint performance bottlenecks and inefficiencies via dynamic modelling techniques. The Ishikawa diagram serves as the primary tool for conducting root-cause analysis. Simultaneously, the 5S methodology is implemented to foster workplace organization, standardization, and hygiene practices. In contrast to traditional optimization frameworks, the proposed strategy integrates real-time performance tracking systems, complemented by adaptive feedback mechanisms. This integration permits ongoing assessment of the production process, facilitating iterative improvement cycles. Empirical data gathered from monitored cycle times, equipment utilization rates, and defect frequencies substantiate the validation of implemented changes. The resulting optimized system significantly minimizes downtime and waste, thereby advancing sustainable and scalable operations. Ultimately, this research demonstrates that the fusion of simulation-based insights with lean management principles leads to considerable improvements in manufacturing productivity and overall product quality.
1 December 2025 in International Journal of Modeling and Optimization
Conductive filaments for Material Extrusion Additive Manufacturing (MEX) can enable low-cost fabrication of functional parts with embedded electrical features. However, systematic studies on process-dependent electrical properties like apparent resistivity and repeatability are limited, and the post-printing stability of the electrical response is not commonly addressed. This study evaluates the influence of printing temperature, printing speed and layer height on the apparent resistivity, specimen-to-specimen repeatability and time-dependent drift of a commercial carbon black-filled conductive PLA filament (ProtoPasta). The novelty of the study consists of evaluating not only the initial apparent resistivity, but also the repeatability between specimens and the post-print drift of apparent resistivity over a 0–50 h interval. The filament was investigated using three printing temperatures (210–230 °C), two printing speeds (60–80 mm/s) and three layer heights (0.2–0.4 mm), with three replicates per configuration. Apparent resistivity ranged between 0.156 and 0.205 kΩ·mm at t0 and between 0.162 and 0.222 kΩ·mm at t50. Multifactorial ANOVA and main-effects analyses showed that the printing temperature was the main factor affecting mean apparent resistivity at both t0 and t50. Higher temperature reduced apparent resistivity, most likely due to improved polymer flow, inter-bead/inter-layer bonding and conductive-network continuity. Printing speed had no significant main effect on the mean apparent resistivity or drift within the tested range. Repeatability depended on the parameter configuration and measurement time, with variability increasing after 24 h and then becoming mainly dependent on layer height. Drift analysis showed a significant main effect of layer height and a significant layer height × temperature interaction, with the largest increase at 0.3 mm. These results show that parameter selection for conductive MEX parts should consider both the initial resistivity level and post-print stability over time.