In this study, an environmentally benign carbon-based catalyst derived from extracted bagasse lignin (EL) was successfully synthesized by solvothermal carbonization and sulfonation with methane sulfonic acid (MSA). Interestingly, the results indicated that the use of MSA as a sulfonation agent made a catalyst with higher thermal stability than conventional sulfuric acid. Thus, in comparison to the catalyst prepared by using sulfuric acid, the catalyst prepared by using MSA (EL- MSA) exhibited higher catalytic activity in the esterification of stearic acid under near-critical methanol conditions. Under optimum conditions (260 degrees C for 5 min, a 9:1 methanol-to-stearic-acid molar ratio, 5 wt % catalyst loading, and 10% v/v toluene), the esterification over the EL- MSA catalyst promoted a 91.1% methyl stearate yield. Moreover, the results also revealed that the high thermal stability of the EL-MSA catalyst not only affects its great catalytic activity, but it also prevents damage to the porous structure and decomposition of acidic surface oxygen-containing functional groups. It contributes to the excellent reusability of the catalyst. After the fifth run, a high yield of 82.8% was obtained. The effect of alcohol type on the catalyst performance was also studied. It was found that the EL-MSA catalyst also presented good performance toward esterification with ethanol and propanol, from which ethyl stearate and propyl stearate with a more than 80% ester yield can be achieved.
A single-bed and dual-bed catalyst system was studied to maximize H2 production from the combination of partial oxidation of CH4 and water gas shift reaction. In addition, the different types of catalysts, including Ni, Cu, Ni-Re, and Cu-Re supported on gadolinium-doped ceria (GDC) were investigated under different operating conditions of temperature (400–650 °C). Over Ni-based catalysts, methane can easily dissociate on a Ni surface to give hydrogen and carbon species. Then, carbon species react with lattice oxygen of ceria-based material to form CO. The addition of Re to Ni/GDC enhances CH4 dissociation on the Ni surface and increases oxygen storage capacity in the catalyst, thus promoting carbon elimination. In addition, the results showed that a dual-bed catalyst system exhibited catalytic activity better than a single-bed catalyst system. The dual-bed catalyst system, by the combination of 1%Re4%Ni/GDC as a partial oxidation catalyst and 1%Re4%Cu/GDC as a water gas shift catalyst, provided the highest CH4 conversion and H2 yield. An addition of Re onto Ni/GDC and Cu/GDC caused an increase in catalytic performance because Re addition could improve the catalyst reducibility and increase metal surface area, as more of their surface active sites are exposed to reactants.
Developing sustainable electrode materials from renewable biomass is important for improving the environmental sustainability of lithium-ion batteries (LIBs). Sugarcane bagasse lignin, an abundant agricultural byproduct, is a promising precursor for lignin-derived carbon anode materials, yet systematic comparative studies on catalyst-dependent structure evolution and LIB performance remain limited. In this study, lignin extracted from sugarcane bagasse by an ethanosolv process was converted into Fe- and Ni-catalyzed lignin-derived carbon materials via catalytic pyrolysis at 900 °C. The effects of catalyst type, metal-to-lignin ratio, and pyrolysis holding time on textural properties, structural features, and electrochemical behavior were systematically investigated. Among the studied conditions, the Fe-catalyzed sample prepared at a metal-to-lignin ratio of 1:2.5 and a holding time of 3 h (GLKL-2.5Fe-3h) exhibited the highest BET surface area (332.71 m2 g−1) and the most developed porous morphology. SEM, TEM, Raman, and XRD analyses indicated catalyst-dependent differences in pore development, carbon domain morphology, and local graphitic ordering, with Fe- and Ni-catalyzed samples following distinct structural evolution pathways. Electrochemical testing showed that GLKL-2.5Fe-3h delivered the highest initial discharge capacity (759 mAh g−1), retained 165 mAh g−1 after 500 cycles, and exhibited more favorable rate performance and lower apparent interfacial resistance than the other tested samples under the same conditions. In contrast, the Ni-catalyzed and solvothermally treated samples showed lower capacity retention and/or less favorable electrochemical behavior. These results demonstrate the strong effect of catalyst type on the structure-performance relationship of bagasse lignin-derived carbon anodes and support Fe-catalyzed lignin-derived carbon as a promising sustainable anode candidate for LIB applications.