This research work aimed to develop smart multifunctional composites via a process for uniformly dispersing carbon nanotubes (CNT) on an orthogonal three-dimensional (3D) woven glass fabric with minimised filtering effect. These smart composites could detect strain under tensile and flexural loading by the piezoresistive response of the infused CNT network. Conventional vacuum assisted resin transfer moulding was modified to control the infusion of 0.25 wt% CNT on the 3D woven glass fabric by varying the vacuum pressure. Results showed that at 101.3 kPa vacuum pressure, the CNT percolated through the thickness of the orthogonal 3D woven glass fabric while being marginally filtered by the fibres and were suitable for sensing tensile strain, whereas at 30.4 kPa, the CNT were deposited only on the surface of the fabric preform without getting filtered and were suitable for sensing flexural strain.
The aim of this study was to develop a process-efficient smart three-dimensional (3D) woven composite T-profile by depositing MXene nanoparticles at the junction for sensing damage and deformation at the junction. Such smart composites could find application in the online health monitoring of complex-shaped parts. The composites were manufactured by infusing epoxy resin in a single-layer fabric T-profile preform, woven in folded form on a dobby shuttle loom using 300 tex glass roving. The chemically etched Ti3C2Tz MXene nanoparticles were dispersed in deionised water and 10 layers were sprayed at the junction of the composite to form a conductive coating. The MXene-coated composite T-profile specimens were subjected to tensile and fatigue loading to study the electromechanical response of the MXene coating to applied displacement. The results showed that the MXene coating was able to sense the sample deformation till ultimate failure of the composite. The MXene coating was also able to effectively sense the tensile–tensile fatigue loading, carried out at 2000 cycles and 4000 cycles for a 50 N–0.5 Hz and a 100 N–1 Hz load–frequency combination, respectively, while being sensitive to the overall deformation of the composite. The smart complex-shaped composites developed in this work were capable of monitoring their health under tensile and fatigue loading in real time.
The study aims to develop a novel method of weaving multiaxis preform on conventional weaving machines and analyse impact tolerance of the ensuing composites along with development of finite element analysis model. An extra set of 200 tex carbon fibres, referred as bias fibres, were integrated into carbon fibre plain woven fabric during the weaving stage on a conventional closed reed weaving machine. This was achieved by partial carbon fibre weft insertion at regular intervals from both edges of the fabric. The multiaxis preform was used as ply on top of plain woven carbon fabric plies, each of 160 g per square meter aerial density. The carbon fibre composites were manufactured by infusing bisphenol F epoxy resin as a matrix and 4 plies of carbon fabric by hand layup method. The composites were subjected to low-velocity impact loading at 0.4 m height of 5.12 kg impactor, and force-time history was recorded by the piezoelectric transducer. A comparison of impact loading results showed that the multiaxis woven composites increase impact strength by 18.3% due to the reinforcement of bias fibre. Based on the test results, a finite element analysis model was developed in Ansys v.19 to simulate the stress distribution during impact loading of the multiaxis woven composites.
This research work is aimed at developing and manufacturing thermoplastic-composite parts for a Type V hydrogen storage tank based on a patented design. A 57% fibre volume fraction of a carbon fibre and polyamide 11 (PA11) thermoplastic matrix was used in an automated tape layup (ATL) process to manufacture a laser-assisted in situ-consolidated composite part for a hydrogen storage vessel. A series of mechanical and thermal tests were performed to optimize the process parameters for composite manufacturing. Based on the optimized process parameters, a scaled-up demonstrator composite part was manufactured and demoulded using pressurized air.
Automated Fiber Placement (AFP) enables precise deposition of thermoplastic tapes on complex geometries, however variations in temperature, compaction pressure, deposition speed, and tooling conditions can affect the final laminate quality. This study presents an integrated real-time monitoring system and a systematic methodology for process/product data analysis linking process parameters to mechanical and microstructural performance. Mechanical testing evaluation by interlaminar shear strength (ILSS), thermal analysis, and microscopy studies identified both the consolidation and mold temperatures as the critical parameters for optimized mechanical properties. Results showed ILSS above 45 MPa, crystallinity up to 37.9%, and minimal porosity (~1%). Digital tools developed provided full traceability, early instability detection, and continuous optimization, enhancing reliability and repeatability in high-performance thermoplastic composite manufacturing, which paves the way towards zero-defect manufacturing.