Promise Nukah

Dr. Promise Nukah

Engineering, Design and Mathematics, The University of the West of England, Bristol, City of Bristol, UK
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
Promise NukahPromise Nukah
Promise Nukah
Samuel AbbeySamuel Abbey
Samuel Abbey
Colin BoothColin Booth
Colin Booth
GNGhassan Nounu
Ghassan Nounu
To improve the prediction of compressive strength and embodied carbon of low carbon concrete using a program algorithm developed in MATLAB, 84 datasets of concrete mix raw materials were used. The influence of water, silica fume and ground granular base slag was found to have a significant impact on the extent of low carbon concrete behaviour in terms of compressive strength and embodied carbon. While the concrete compressive strength for normal concrete increases with reducing water content, it is observed that the low carbon concrete using lightweight aggregate material increases in compressive strength with an increase in embodied carbon. From the result of the analysis, a function was developed that was able to predict the associated embodied carbon of a concrete mix for a given water-to-cement ratio. The use of an alkaline solution is observed to increase the compressive strength of low carbon concrete when used in combination with ground granular base slag and silica fume. It is further shown that ground granular base slag contributes significantly to an increase in the compressive strength of Low carbon concrete when compared with pulverised fly ash. The optimised mix design program resulted in a 26% reduction in embodied carbon and an R2 value of 0.9 between the measured compressive strength and the optimised compressive strength.

17 September 2023 in Construction and Building Materials
Verified
Journal Article
Open access
Promise NukahPromise Nukah
Promise Nukah
Samuel AbbeySamuel Abbey
Samuel Abbey
Colin BoothColin Booth
Colin Booth
GNGhassan Nounu
Ghassan Nounu

14 December 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
Promise NukahPromise Nukah
Promise Nukah
Samuel AbbeySamuel Abbey
Samuel Abbey
Colin BoothColin Booth
Colin Booth
Jonathan OtiJonathan Oti
Jonathan Oti
Evaluation of the effect of embodied carbon reduction using an optimized design section for a ground beam, use of supplementary cementitious materials, and replacement of normal aggregate with light weight aggregate on the mechanical properties of low-carbon concrete was carried out. A creep coefficient of 0.019 was estimated for a 365-day period on a change in section from 1 to 0.6 m2 on a proposed trapezoidal section for ground beam, which showed a negligible difference when compared to the normal rectangular section owing to a reduction in embodied carbon due to the associated reduction in concrete volume and reinforcement. Training of 81 low-carbon concrete data sets in MATLAB using artificial neural network for 100% cement replacement with ground granular base slag indicates good performance with a mean square error of 0.856. From the study, it was observed that the extent of carbonation depth in concrete evidenced the measure of compressive strength formation based on the specific surface area of the binder and the water absorption rate of the aggregate, while enhancing the flexural strength of the low-carbon concrete required a cement-to-supplementary-cementitious-material ratio of 0.8.

23 December 2025 in Discover Civil Engineering
Verified
Journal Article
Open access
PDF file
Promise NukahPromise Nukah
Promise Nukah
Samuel AbbeySamuel Abbey
Samuel Abbey
Colin BoothColin Booth
Colin Booth
The widespread deployment of low-carbon and alternative cementitious concretes necessitates a critical evaluation of current design standards, particularly those governing the ultimate compressive strain and its implications for flexural behaviour in reinforced concrete (RC) elements. This study examines the effect of reduced ultimate compressive strain on the position of the neutral axis, the minimum lever arm factor (Kbal), and associated reinforcement requirements in RC beam design. A strain-adaptive analytical model was developed to quantify the shift in neutral axis depth (x) relative to the effective depth (d) and the corresponding variation in Kbal for concretes exhibiting strain capacities below the conventional Eurocode 2 assumption of 0.0035. Results indicate a progressive increase in x/d from 0.36 to 0.90 as strain capacity decreases, with Kbal values ranging from 0.253 to 0.304. Application of the model to a case study demonstrated a potential reduction of up to 680 mm² in required reinforcement for a 6m length of reinforced concrete beam , yielding significant material and embodied carbon savings. This underscores the need for performance-based design methodologies that reflect the evolving mechanical behaviour of sustainable concrete materials, offering a pathway toward more efficient and resilient structural systems. Based on embodied carbon factor of 0.684 kgCO₂e/kg for rebar, this reduction corresponds to a carbon saving of approximately 21.91kgCO₂e per 6 m length of RC beam. These findings highlight the dual structural and environmental benefits of strain-adaptive design and reinforce the need for performance-based methods that account for the evolving mechanical properties of sustainable concrete materials, supporting more efficient, economical, and low-carbon structural solutions.