Rabah Mahmoud Ahmad Ismail

Dr. Rabah Mahmoud Ahmad Ismail

Civil Engineering, Jadara University, Irbid, Jordan
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 January 2026 in International Journal of Information Technology
Verified
Journal Article
Closed access
PDF file
ITIssam Trrad
Issam Trrad
Rabah Mahmoud Ahmad IsmailRabah Mahmoud Ahmad Ismail
Rabah Mahmoud Ahmad Ismail
HAHashem Al-Mattarneh
Hashem Al-Mattarneh
SHSnehal Hole
Snehal Hole

14 December 2020 in Applied and Environmental Soil Science
Verified
Journal Article
Open access
PDF file
MDMohammed Dahim
Mohammed Dahim
MAMusab Abuaddous
Musab Abuaddous
Rabah Mahmoud Ahmad IsmailRabah Mahmoud Ahmad Ismail
Rabah Mahmoud Ahmad Ismail
HAHashem Al-Mattarneh
Hashem Al-Mattarneh
AJAiman Qasem Jaradat
Aiman Qasem Jaradat
This paper presents a new method of dielectric capacitance cell as a proposed device for measuring the impedance of pure sand artificially contaminated with four heavy metals. Dielectric constant and loss factor of clean and contaminated sand at various levels were calculated from the measured sand impedances. The advantages and benefits of using the proposed dielectric capacitance cell were its low cost, simple calculation, calibration procedures, portable and lightweight, and easy to modify the electrodes to suit testing in the field. Pure sand was saturated with water artificially polluted in the lab with Pb, Cd, Fe, and Zn at heavy metal contents 0, 7.5, 15, 22.5, and 30 mg/kg of sand. The dielectric properties of polluted sand were evaluated at a frequency range from 100 kHz to 1000 kHz. The polluted sand exhibit different dielectric constants and loss factors from the unpolluted sand. The results also indicate that the dielectric constant decreases with increasing pollution level for all heavy metals. This may attribute to the polarization mechanism change with existing heavy metal. The loss factor of sand increases with the increasing pollution level. This may be explained by the increase of ionic conductivity of pore water with heavy metal in the sand. Sand polluted with heavy metal with higher resistivity and density possess a higher dielectric constant and lower loss factor than other polluted metals. Evaluation of the dielectric characteristics of polluted sand could have the potential to monitor heavy metal pollution. Even with promising results obtained with the proposed dielectric device, it is necessary to explore several other factors affecting the measurements such as sand water content, soil texture, and type of soil. Also, testing polluted soil near industrial pollution is needed.

8 April 2024 in Asian Journal of Civil Engineering
Verified
Journal Article
Closed access
PDF file
Rabah Mahmoud Ahmad IsmailRabah Mahmoud Ahmad Ismail
Rabah Mahmoud Ahmad Ismail
JAJamal Alsadi
Jamal Alsadi
RHRanda Hatamleh
Randa Hatamleh
DTDUAA Basem Telfah
DUAA Basem Telfah
AJAiman Qasem Jaradat
Aiman Qasem Jaradat
HAHashem Al-Mattarneh
Hashem Al-Mattarneh

14 October 2024 in Asian Journal of Civil Engineering
Verified
Journal Article
Closed access
PDF file
HNHamsa Nimer
Hamsa Nimer
Rabah Mahmoud Ahmad IsmailRabah Mahmoud Ahmad Ismail
Rabah Mahmoud Ahmad Ismail
HAHashem Al-Mattarneh
Hashem Al-Mattarneh
MKMohanad Khodier
Mohanad Khodier
YJYaser Jaradat
Yaser Jaradat
MRMohammad Rawashdeh
Mohammad Rawashdeh


11 November 2022 in Polymers
Verified
Journal Article
Open access
PDF file
JAJamal Alsadi
Jamal Alsadi
MOMohammed Taleb Obaidat
Mohammed Taleb Obaidat
Rabah Mahmoud Ahmad IsmailRabah Mahmoud Ahmad Ismail
Rabah Mahmoud Ahmad Ismail
ITIssam Trrad
Issam Trrad
MAMarwa Aljamal
Marwa Aljamal
HAHashem Al-Mattarneh
Hashem Al-Mattarneh
Incorporating pigments into polymers can be done for various purposes, including the introduction of color, interfacial effects, or aesthetics. If these pigments are to disperse properly, then the process of extrusion must be optimized. During polymer compounding extrusion, three effective processing factors were investigated: feed rate (FR), speed (Sp.) and temperature (temp.) for a colored compounded polycarbonate (PC) grade (30/70%). The processing design techniques were obtained by applying design experiments in a response surface methodology (RSM) to blend two polycarbonates with pigments and optimize the processing temperatures at center points. The first study decided to utilize the response surface approach of Box–Behnken design (BBD) to design an experiment to optimize the process parameters. Statistical significance was demonstrated by the model passing all diagnostic tests. Furthermore, the three processing factors strongly impacted the characteristics of the tri-stimulus color, according to the results from a variance analysis. The second study identified process variables for the same PC grade at the center level, 25 kg/h FR, 750 rpm speed, and (255 °C) temp. The characterization and scanning morphology were examined using MicroCtscanner image analysis, SEM, DOM, rheology, FT-IR, and color-pigmented values were measured using a color spectrometer. The output response was significantly impacted when excellent color dispersion was observed with few agglomerates and less differences in colors at the center point. By characterizing these results and having good insight into color difference output and processing condition relationships, which have an adverse effect on color variation characteristics and minimize recycling compounds of different grades, results in cleaner environments benefits.