Roya Ermagan

Ms. Roya Ermagan

University of Southern California
orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 December 2019 in Metals
Verified
Journal Article
Open access
PDF file
michael e kassnermichael e kassner
michael e kassner
RERoya Ermagan
Roya Ermagan
New analysis provides insight into the basis of power-law breakdown (PLB) in the steady-state creep of metals and alloys. A variety of theories has been presented in the past but this new examination suggests that there is evidence that a dramatic supersaturation of vacancies leading to very high diffusion rates and enhanced dislocation climb is associated with the rate-controlling process for creep in PLB. The effect of vacancy supersaturation may be enhanced by dislocation short circuit diffusion paths at lower temperatures due to the dramatic increase in dislocation density.

26 April 2017 in Micromachines
Verified
Journal Article
Open access
PDF file
KBKrisna Bhargava
Krisna Bhargava
RERoya Ermagan
Roya Ermagan
BTBryant Thompson
Bryant Thompson
AFAndrew Friedman
Andrew Friedman
NMNoah Malmstadt
Noah Malmstadt
3D printing facilitates the straightforward construction of microchannels with complex three-dimensional architectures. Here, we demonstrate 3D-printed modular mixing components that operate on the basis of splitting and recombining fluid streams to decrease interstream diffusion length. These are compared to helical mixers that operate on the principle of chaotic advection.

21 June 2017 in Metallurgical and Materials Transactions A
Verified
Journal Article
Closed access
PDF file
michael e kassnermichael e kassner
michael e kassner
CCC. S. Campbell
C. S. Campbell
RERoya Ermagan
Roya Ermagan

14 April 2017 in Preprints.org
Verified
Preprint
Open access
PDF file
KBKrisna Bhargava
Krisna Bhargava
RERoya Ermagan
Roya Ermagan
BTBryant Thompson
Bryant Thompson
AFAndrew Friedman
Andrew Friedman
NMNoah Malmstadt
Noah Malmstadt
3D printing facilitates the straightforward construction of microchannels with complex three-dimensional architectures. Here, we demonstrate 3D-printed modular mixing components that operate on the basis of splitting and recombining fluid streams to decrease interstream diffusion length. These are compared to helical mixers that operate on the principle of chaotic advection.

15 April 2020 in Metals
Verified
Journal Article
Open access
PDF file
RERoya Ermagan
Roya Ermagan
MSMaxime Sauzay
Maxime Sauzay
michael e kassnermichael e kassner
michael e kassner
There have been a number of studies on dipole separations in cyclically deformed FCC single crystals in single slip while there are no such studies in multiple slip. The dipole heights provide insight into the presence of long-range internal stresses (LRIS). In this study, we investigated how LRIS compare with the single slip studies through measuring the dislocation of dipole heights. [001] oriented copper single crystals were cyclically deformed in strain-control to saturation at ambient temperature. Transmission electron microscopy (TEM) confirms a labyrinth dislocation microstructure with high dislocation density walls and low dislocation density channels. The maximum dipole heights under the saturation stress were approximately independent of location, being nearly equal in the walls and within the channels. This, by itself, supports a uniform stress across the microstructure and low long-range internal stresses. The maximum value for dipole heights suggests dipole strengths (local stresses) that are about a factor of 2.4 higher than the applied stress based on the usual athermal equations. Considering the small “extra” stress that may be provided by tripoles or small dislocation pile-ups, a nearly homogenous stress distribution with only small internal stresses may be present, which is consistent with the observation of uniform dipole height across the heterogeneous dislocation microstructure. This observation that the stress state appears to be homogenous and higher than the applied stress has also been reported in the case of cyclically deformed metals in single slip.

24 November 2020 in Crystals
Verified
Journal Article
Open access
PDF file
RERoya Ermagan
Roya Ermagan
MSMaxime Sauzay
Maxime Sauzay
MMMatthew Mecklenburg
Matthew Mecklenburg
michael e kassnermichael e kassner
michael e kassner
Understanding long range internal stresses (LRIS) may be crucial for elucidating the basis of the Bauschinger effect, plastic deformation in fatigued metals, and plastic deformation in general. Few studies have evaluated LRIS using convergent beam electron diffraction (CBED) in cyclically deformed single crystals oriented in single slip and there are no such studies carried out on cyclically deformed single crystals in multiple slip. In our earlier and recent study, we assessed the LRIS in a cyclically deformed copper single crystal in multiple slip via measuring the maximum dislocation dipole heights. Nearly equal maximum dipole heights in the high dislocation density walls and low dislocation density channels suggested a uniform stress state across the labyrinth microstructure. Here, we evaluate the LRIS by determining the lattice parameter in the channels and walls of the labyrinth dislocation structure using CBED. Findings of this work show that lattice parameters obtained were almost equal near the walls and within the channels. Thus, a homogenous stress state within the heterogeneous dislocation microstructure is again suggested. Although the changes in the lattice parameter in the channels are minimal (less than 10−4 nm), CBED chi-squared analysis suggests that the difference between the lattice parameter values of the cyclically deformed and unstrained copper are slightly higher in the proximity of the walls in comparison with the channel interior. These values are less than 6.5% of the applied stress. It can be concluded that the dominant characteristics of the Bauschinger effect may need to include the Orowan-Sleeswyk mechanism type of explanation since both the maximum dipole height measurements and the lattice parameter assessment through CBED analysis suggest a homogenous stress state. This work complements our earlier work that determined LRIS based on dipole heights by assessing LRIS through a different methodology, carried out on a cyclically deformed copper single crystal oriented for multiple slip.