The use of fossil fuels in modern economies has been a success because of the low cost of fossil resources. However, the depletion of fossil reserves, the increase in waste production and global warming concerns have led to increased research on the production of biofuels from renewable resources. Waste production is steadily increasing in quantity and constantly changing in quality, creating enormous risks for the environment and, consequently, for the health of the population. This situation is much more worrying in developing countries, in particular because of the considerable delay in the field of the conversion and recovery of biomaterials, due to their difficulty in approaching the problem in a way that fits their context. The composition of such wastes and residues, rich in organic matter, allows their conversion via biochemical mechanisms, thus constituting an effective solution to address the environmental problems of their disposal. Anaerobic digestion remains a valuable and effective technology for transforming these biomaterials into biogas. The present review focuses on technologies, challenges and areas of application of biogas, especially in China and some African countries, in order to promote the large-scale use of biogas for electricity generation and biofuels. Results point out that China is more used to this technology, while African countries still rely on traditional and less advanced technologies, thus hampering the potential derived from the large availability of biomaterials. Both realities, however, share similar backgrounds about the dimension of the biogas plants and their non-commercial purposes, even if China is recently shifting toward the adoption of a different model. These considerations are used in the article to open an interesting new scenario of political alternatives which may provide a way out from poverty and economic dependence, within the framework of a wider circularity.

Optimize the main influencing factors in the synthesis of high performance materials (activated carbon) obtained from coffee husk as a widely available lignocellulosic precursor and study its textural and chemical characteristics.

The yields in bioconversion of residues produced in the Cameroon food industry to liquid and gaseous biofuels were evaluated and the potential of these residues as feedstock for renewable energy production in Cameroon were assessed. Residues generated after processing avocado, cocoa, and peanut crops were converted at laboratory-scale to second-generation gaseous biofuels (biogas) and liquid biofuels (ethanol). Mechanical (milling), thermal-chemical (steam-NaOH), and microwave pretreatments were applied before hydrolysis of biomass using cellulolytic enzymes. Cellulosic sugars production potential was also assessed. The energy conversion rate was higher when anaerobic digestion technology was applied to convert the tested biomass to methane. The total Cameroon potential under anaerobic digestion technology is over 330,000 m3, which represents 28% from oil consumption or 5.39% from electricity consumption when lignocellulosic ethanol technology was applied. The national potential was assessed up to 200,000 kg, representing 17% from oil consumption in transport or 3.19% from electricity consumption. Overall, the share of energy potential of the tested residual biomass is important when compared to fossil fuel consumption in Cameroon and represents an important potential feedstock for electricity production.

In this work, biomass lignocellulosic materials extracted via chemical and physical treatments from bean and pistachio pod waste were used for the optimized elimination of Indigo Carmine (IC) from aqueous medium, using a design of experiments methodology. The physicochemical properties of the studied materials (raw and treated counterparts) used for the sorption of IC were investigated by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM) coupled with EDX, and thermal analysis. Key variables influencing the adsorption of IC, namely the initial IC concentration, the pH of the solution, the stirring time and the mass of adsorbents, were optimized by the central composite design (CCD) with three center points, the measured response being the amount of IC adsorbed. The optimal conditions obtained from the statistical analysis for the removal of IC were as follows: maximum adsorbed amounts of IC: 1.81 mg/g, 2.05 mg/g, 3.56 mg/g; 7.42 mg/g, 8.95 mg/g, 15.35 mg/g, for raw bean pods (RBS), BST1 and BST2 (bean pods chemically treated), and for raw pistachio pods (RPS), PST1 and PST2 (pistachio pods chemically treated), respectively. The pseudo-second-order nonlinear kinetics model well described the IC adsorption kinetics for RBS, BST1 and BST2, while the Elovich model was properly fitted by RPS, PST1, and PST2 biomaterials data. The Freundlich isotherm best described the shrinkage of IC on different sorbents. The good correlation of the experimental data of the IC with respect to the Freundlich isotherm indicated a multilayer adsorption with heterogeneous adsorption sites and different energies. The interest of this work consisted in developing analytical methods for the treatment of water polluted by dyes by using biosorbents, local biological materials widely available and inexpensive. The results collected in this work highlighted the interesting structural, morphological, and physico-chemical properties of the agro-waste used in the study, which properties allowed an important fixation of the target dye in solution. The research showed that the agro-waste used in the study are possible precursors to locally manufacture adsorbents at low cost, thus allowing the efficient removal of waste and dyes in liquid effluents.