Sergey Vinogradov

Dr. Sergey Vinogradov


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 May 2018 in Materials
Verified
Journal Article
Open access
PDF file
SVSergey Vinogradov
Sergey Vinogradov
ACAdam Cobb
Adam Cobb
JFJay L Fisher
Jay L Fisher
Magnetostrictive transduction has been widely utilized in nondestructive evaluation (NDE) applications, specifically for the generation and reception of guided waves for the long-range inspection of components such as pipes, vessels, and small tubes. Transverse-motion guided wave modes (e.g., torsional vibrations in pipes) are the most common choice for long-range inspection applications, because the wave motion is in the plane of the structure surface, and therefore does not couple well to the surrounding material. Magnetostrictive-based sensors for these wave modes using the Wiedemann effect have been available for several years. An alternative configuration of a sensor for generating and receiving these transverse-motion guided waves swaps the biasing and time-varying magnetic field directions. This alternative design is a reversed Wiedemann effect magnetostrictive transducer. These transducers exhibit a number of unique features compared with the more conventional Wiedemann sensor, including: (1) the use of smaller rare earth permanent magnets to achieve large, uniform, and self-sustained bias field strengths; (2) the use of more efficient electric coil arrangements to induce a stronger time-varying magnetic field for a given coil impedance; (3) beneficial non-linear operating characteristics, given the efficiency improvements in both magnetic fields; and (4) the ability to generate unidirectional guided waves when the field arrangement is combined with a magnetically soft ferromagnetic strip (patch). Reversed Wiedemann effect magnetostrictive transducers will be presented that are suitable for different inspection applications, one using electromagnetic generation and reception directly in a ferromagnetic material, and another design that integrates a magnetostrictive patch to improve its efficiency and enable special operating characteristics.

1 January 2017 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
SVSergey Vinogradov
Sergey Vinogradov
ACAdam Cobb
Adam Cobb
GLGlenn Light
Glenn Light
Magnetostrictive transduction has been widely utilized in NDE applications, specifically for generation and reception of guided waves for long-range inspection of components such as pipes, vessels, and small tubes. Transverse-motion guided wave modes (e.g., torsional vibrations in pipes) are the most typical choice for long-range inspection applications because the wave motion is in the plane of the structure. Magnetostrictive-based sensors have been available for several years for these wave modes based on the Wiedemann effect. For these sensors, a permanent magnetic bias is applied that is perpendicular to the direction of the propagated guided wave. This bias field strains the material that the guided wave is generated in preferentially in the desired particle motion direction. A time-varying magnetic field oriented parallel to the direction of guided wave propagation is also induced in the material. This time-varying field is induced using an electric coil located near the material surface. The interaction of these two fields produces the guided waves; an inverse effect is used for the receive process. An alternative configuration of a sensor for generating and receiving these traverse-motion guided waves is to swap the biasing and time-varying magnetic fields directions. Since transverse-motion guided wave sensors are typically much longer in the particle motion direction than in the bias field direction, the net effect of this alternative design is that the magnetic biasing length is shorter and different coil designs can be used. Because of this, the alternative design, known as a magnetostrictive transducer (MsT), exhibits a number of unique features compared to the Wiedemann sensor described above, such as: 1) the ability to use smaller rare earth permanent magnets and achieve uniform and self-sustained bias field strengths, 2) the choice of more efficient electric coil arrangements to induce a stronger time-varying magnetic field for a given coil impedance, 3) more easily exhibit nonlinear operating characteristics given the efficiency improvements in both magnetic fields, and 4) the ability to generate unidirectional guided waves when the field arrangement is combined with a magnetically soft ferromagnetic strip (patch). MsT designs will be presented that are suitable for different inspection applications, one using electromagnetic generation and reception directly in a ferromagnetic material and another design that integrates a magnetostrictive patch to improve the efficiency and allow special operating characteristics.

14 February 2026 in Sensors
Verified
Journal Article
Open access
PDF file
SVSergey Vinogradov
Sergey Vinogradov
NANikolay Akimov
Nikolay Akimov
ACAdam Cobb
Adam Cobb
JFJay L Fisher
Jay L Fisher
Aboveground storage tanks are used to store various fluids and chemicals for many industrial purposes. According to API standard 653, the structural integrity of these tanks must be regularly assessed. The U.S. EPA requires each operator to have a Spill Prevention, Control and Countermeasure Plan (SPCC) for aboveground storage containers. The accepted practice for inspection of these tanks, particularly the tank bottoms, requires removing the tank from service, emptying the tank, and interior entry for direct inspection of the structure. The required inspection operations are hazardous due to the chemicals themselves as well as the requirement to operate within confined spaces. An inspection from outside the tank would have significant cost and time benefits and would provide a large reduction in the risks faced by inspection personnel. Guided wave (GW) testing is a promising candidate for screening of storage tank walls and bottoms from the tank exterior due to the ability of GWs to propagate over long distances from a fixed probe location. The lowest-order transverse-motion guided wave modes (e.g., torsional vibrations in pipes) are a good choice for long-range inspection because this mode is not dispersive; therefore, the wave packets do not spread out in time. A common weakness of guided wave inspection is the complexity of report generation in the presence of multiple geometry features in the structure, such as welds, welded plate corners, attachments and so on. In some cases, these features cause generation of non-relevant indications caused by mode conversion. Another significant challenge in applying GW testing is development of probes with high-enough signal amplitudes and relatively small footprints to allow them to be mounted on short tank bottom extensions. In this paper, a new generation of magnetostrictive transducers will be presented. The transducers are based on the reversed Wiedemann effect and can generate shear horizontal mode guided waves over a wide frequency range (20–150 kHz) with SNRs in excess of 50 dB. The recently developed SwRI MST 8 × 8 probe contains an array of eight pairs of individual magnetostrictive transducers (MsTs). The data acquisition hardware allows acquisition using Full Matrix Capture (FMC) and analysis software reporting of anomalies based on Total Focusing Method (TFM) image reconstruction. This novel inspection package allows generation of reports that map out corrosion locations and provide estimates of defect widths. Case studies of this technology on actual storage tank walls and bottoms will be presented together with validation of processing methods on mockups with known anomalies and geometry features.

1 January 2018 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
PDF file
SVSergey Vinogradov
Sergey Vinogradov
ACAdam Cobb
Adam Cobb
JBJonathan Bartlett
Jonathan Bartlett
YUYouichi Udagawa
Youichi Udagawa
The application of guided waves for the testing of plate-type structures has been recently investigated by a number of research groups due to the ability of guided waves to detect corrosion in remote and hidden areas. Guided wave sensors for plate applications can be either directed (i.e., the waves propagate in a single direction) or omnidirectional. Each type has certain advantages and disadvantages. Omnidirectional sensors can inspect large areas from a single location, but it is challenging to define where a feature is located. Conversely, directed sensors can be used to precisely locate an indication, but have no sensitivity to flaws away from the wave propagation direction. This work describes a newly developed sensor that combines the strengths of both sensor types to create a novel omnidirectional transducer. The sensor transduction is based on a custom magnetostrictive transducer (MsT). In this new probe design, a directed, plate-application MsT with known characteristics was incorporated into an automated scanner. This scanner rotates the directed MsT for data collection at regular intervals. Coupling of the transducer to the plate is accomplished using a shear wave couplant. The array of data that is received is used for compiling B-scans and imaging, utilizing a synthetic aperture focusing algorithm (SAFT). The performance of the probe was evaluated on a 0.5-inch thick carbon steel plate mockup with a surface area of over 100 square feet. The mockup had a variety of known anomalies representing localized and distributed pitting corrosion, gradual wall thinning, and notches of different depths. Experimental data was also acquired using the new probe on a retired storage tank with known corrosion damage. The performance of the new sensor and its limitations are discussed together with general directions in technology development.

9 January 2026 in Preprints.org
Verified
Preprint
Open access
PDF file
SVSergey Vinogradov
Sergey Vinogradov
NANikolay Akimov
Nikolay Akimov
ACAdam Cobb
Adam Cobb
JFJay L Fisher
Jay L Fisher
Above ground storage tanks are used to store various fluids and chemicals for many industrial purposes. According to API standard 653, the structural integrity of these tanks must be regularly assessed. The U.S. EPA requires each operator to have a Spill Prevention, Control and Countermeasure Plan (SPCC) for aboveground storage con-tainers. The accepted practice for inspection of these tanks, particularly the tank bot-toms, involves removing the tank from service, emptying the tank, and inspecting di-rectly from the interior. The required inspection operations are hazardous due to the chemicals themselves as well as the requirement to operate within confined spaces. An inspection from outside the tank would have significant cost and time benefits and would provide a large reduction in the risks faced by the inspection personnel. Guided wave (GW) testing is one promising candidate for screening of storage tanks walls and bottoms from the tank exterior due to the ability of GWs to propagate long distances from a fixed probe location. The lowest order transverse-motion guided wave modes (e.g., torsional vibrations in pipes) are a good choice for long-range inspection because this mode is not dispersive; therefore, the wave packets do not spread out in time. A common weakness of guided wave inspection is the complexity of report generation in the presence of multiple geometry features in the structure, such as welds, welded plate corners, attachments and so on. In some cases, these features cause generation of non-relevant indications due to mode conversion. Common non-relevant indications are described in this paper. Another significant challenge in applying GW testing is development of probes with high enough signal amplitudes and a relatively small footprint to allow them to be mounted on relatively short tank bottom extensions. In this paper a new generation of magnetostrictive transducers will be presented. The transducers are based on a reversed Wiedemann effect and can generate shear hori-zontal mode guided waves over a wide frequency range (20 – 150 kHz) and with SNR in excess of 50 dB. The recently developed SwRI MST 8x8 probe contains an array of 8 pairs of individual magnetostrictive transducers (MsTs). The data acquisition hard-ware allows acquisition using Full Matrix Capture (FMC) and analysis software re-porting of anomalies based on Total Focusing Method (TFM) image reconstruction. This novel inspection package allows generation of reports containing high accuracy corrosion mapping information. Case studies of this technology on actual storage tanks walls and bottoms will be presented together with validation of processing methods on mockups with known anomalies and geometry features.