Shara K Mohammed

Dr. Shara K Mohammed

Petroleum Technology Department, Erbil Polytechnic University, Erbil, Arbīl, Iraq
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2021 in Chemical Engineering Research and Design
Verified
Journal Article
Closed access
AHAbbas H. Hasan
Abbas H. Hasan
SMShara K Mohammed
Shara K Mohammed
BHB. Hewakandamby
B. Hewakandamby
BABarry Azzopardi
Barry Azzopardi

2 September 2021 in The Canadian Journal of Chemical Engineering
Verified
Journal Article
Open access
PDF file
SMShara K Mohammed
Shara K Mohammed
AHAbbas H. Hasan
Abbas H. Hasan
AIAbubakr Ibrahim
Abubakr Ibrahim
GDGeorgios Dimitrakis
Georgios Dimitrakis
Gas‐viscous liquid bubbly and slug flow are very common in petroleum, chemical, bioengineering, polymer, and food processing. However, there is a major knowledge gap in two‐phase flow research in the design of gas injectors/distributers in very high viscosity oil systems. The present study investigates the effect of gas injection methods in columns containing very high viscosity oils (i.e., realistic liquids), and more specifically using 360 Pa · s viscosity oil in a 240‐mm diameter column. The effects that the radial positioning, number of gas nozzles, and their distance from each other have on the structure of the flow in viscous liquids are presented in detail. Electrical capacitance tomography (ECT) is used to extract experimental data. Void fraction, bubble velocity, frequency, liquid film thickness, and bubble length were measured and analyzed at different radial gas injection positions. It has been observed that bubble length increases significantly by 0.3 m when the injection nozzle is located next to the wall of the pipe. Bubble velocity and length also increase by 0.217 m/s and 3.6 m, respectively, with increasing gas flowrate when multiple injection points are used. Increasing the distance between the gas injection points increased bubbles' length by 1.2 m. Bubbles' velocity and frequency (at higher gas flow rate) were also increased.

24 February 2026 in Chemengineering
Verified
Journal Article
Open access
PDF file
AHAbbas H.A.M. Hasan
Abbas H.A.M. Hasan
SMShara K Mohammed
Shara K Mohammed
BHBuddhika Hewakandamby
Buddhika Hewakandamby
FSFaiza SAIDJ
Faiza SAIDJ
AAAbdelwahid Azzi
Abdelwahid Azzi
BABarry James Azzopardi
Barry James Azzopardi
Many of the film thickness measurements that have been reported in the literature tend to focus on small pipe diameters, which may not be practical for a variety of industrial applications. Additionally, single-point measurements are unable to provide the necessary film thickness data around the circumference of the pipe as well as in the axial direction. This paper aims to experimentally study the behaviour of wavy liquid films, including wave frequency, wave velocity, wave width, and wave spacing. A Multi-Pin Film Sensor (MPFS) was used to extract the thickness of a free-falling liquid film in axial, circumferential, and temporal coordinates. The range of liquid Reynolds number ReL used was 618–1670. It was found that the power spectral density of the disturbance waves showed a pronounced peak at the modal frequency of 6–8 Hz. The number of disturbance waves was found to be almost independent of ReL. The axial interfacial wave seemed to travel at a constant velocity while the mean velocity in circumferential direction was negligible. The mean width of the disturbance waves was approximately 17.7% of the pipe diameter.

17 April 2022 in International Journal of Multiphase Flow
Verified
Journal Article
Open access
SMShara K Mohammed
Shara K Mohammed
AHAbbas H. Hasan
Abbas H. Hasan
Georgios DimitrakisGeorgios Dimitrakis
Georgios Dimitrakis
BABarry J. Azzopardi
Barry J. Azzopardi