Shiva Shirani

Dr. Shiva Shirani

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2021 in Cement and Concrete Research
Verified
Journal Article
Closed access
SSShiva Shirani
Shiva Shirani
ACANA CUESTA
ANA CUESTA
AMAlejandro Morales-Cantero
Alejandro Morales-Cantero
ATAngeles G. De la Torre
Angeles G. De la Torre
MOMargie P. Olbinado
Margie P. Olbinado
Miguel A. G. ArandaMiguel A. G. Aranda
Miguel A. G. Aranda

8 May 2023 in Nature Communications
Verified
Journal Article
Open access
PDF file
SSShiva Shirani
Shiva Shirani
ACAna Cuesta
Ana Cuesta
AMAlejandro Morales-Cantero
Alejandro Morales-Cantero
ISIsabel Santacruz
Isabel Santacruz
ADAna Diaz
Ana Diaz
Miguel A. G. ArandaMiguel A. G. Aranda
Miguel A. G. Aranda
Despite a century of research, our understanding of cement dissolution and precipitation processes at early ages is very limited. This is due to the lack of methods that can image these processes with enough spatial resolution, contrast and field of view. Here, we adapt near-field ptychographic nanotomography to in situ visualise the hydration of commercial Portland cement in a record-thick capillary. At 19 h, porous C-S-H gel shell, thickness of 500 nm, covers every alite grain enclosing a water gap. The spatial dissolution rate of small alite grains in the acceleration period, ∼100 nm/h, is approximately four times faster than that of large alite grains in the deceleration stage, ∼25 nm/h. Etch-pit development has also been mapped out. This work is complemented by laboratory and synchrotron microtomographies, allowing to measure the particle size distributions with time. 4D nanoimaging will allow mechanistically study dissolution-precipitation processes including the roles of accelerators and superplasticizers.

1 November 2020 in Cement and Concrete Research
Verified
Journal Article
Closed access
SSShiva Shirani
Shiva Shirani
ACA. Cuesta
A. Cuesta
ATA.G. De la Torre
A.G. De la Torre
ADA. Diaz
A. Diaz
PTP. Trtik
P. Trtik
MAM.A.G. Aranda
M.A.G. Aranda

14 November 2023 in Cement and Concrete Research
Verified
Journal Article
Open access
SSShiva Shirani
Shiva Shirani
ACANA CUESTA
ANA CUESTA
ATAngeles G De la Torre
Angeles G De la Torre
ISI. Santacruz
I. Santacruz
AMA. Morales-Cantero
A. Morales-Cantero
Miguel A. G. ArandaMiguel A. G. Aranda
Miguel A. G. Aranda

4 July 2024 in Journal of Applied Crystallography
Verified
Journal Article
Open access
PDF file
JFJaime Fernandez-Sanchez
Jaime Fernandez-Sanchez
ACANA CUESTA
ANA CUESTA
SSShiva Shirani
Shiva Shirani
CRCinthya Redondo-Soto
Cinthya Redondo-Soto
ATAngeles G De la Torre
Angeles G De la Torre
Miguel A. G. ArandaMiguel A. G. Aranda
Miguel A. G. Aranda
Portland cements (PCs) and cement blends are multiphase materials of different fineness, and quantitatively analysing their hydration pathways is very challenging. The dissolution (hydration) of the initial crystalline and amorphous phases must be determined, as well as the formation of labile (such as ettringite), reactive (such as portlandite) and amorphous (such as calcium silicate hydrate gel) components. The microstructural changes with hydration time must also be mapped out. To address this robustly and accurately, an innovative approach is being developed based on in situ measurements of pastes without any sample conditioning. Data are sequentially acquired by Mo K α 1 laboratory X-ray powder diffraction (LXRPD) and microtomography (µCT), where the same volume is scanned with time to reduce variability. Wide capillaries (2 mm in diameter) are key to avoid artefacts, e.g. self-desiccation, and to have excellent particle averaging. This methodology is tested in three cement paste samples: (i) a commercial PC 52.5 R, (ii) a blend of 80 wt% of this PC and 20 wt% quartz, to simulate an addition of supplementary cementitious materials, and (iii) a blend of 80 wt% PC and 20 wt% limestone, to simulate a limestone Portland cement. LXRPD data are acquired at 3 h and 1, 3, 7 and 28 days, and µCT data are collected at 12 h and 1, 3, 7 and 28 days. Later age data can also be easily acquired. In this methodology, the amounts of the crystalline phases are directly obtained from Rietveld analysis and the amorphous phase contents are obtained from mass-balance calculations. From the µCT study, and within the attained spatial resolution, three components (porosity, hydrated products and unhydrated cement particles) are determined. The analyses quantitatively demonstrate the filler effect of quartz and limestone in the hydration of alite and the calcium aluminate phases. Further hydration details are discussed.

17 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
ISInés Ruiz Salcedo
Inés Ruiz Salcedo
ACANA CUESTA
ANA CUESTA
SSShiva Shirani
Shiva Shirani
LLLaura Leon-Reina
Laura Leon-Reina
Miguel A. G. ArandaMiguel A. G. Aranda
Miguel A. G. Aranda
Cement hydration is a very complex set of processes. The evolution of the crystalline phases during hydration can be accurately followed by X-ray powder diffraction data evaluated by the Rietveld method. However, accurate measurements of some microstructural features, including porosity and amorphous content developments, are more challenging. Here, we combine laboratory X-ray powder diffraction and computed microtomography (μCT) to better understand the results of the μCT analyses. Two pastes with different water–cement ratios, 0.45 and 0.65, filled within capillaries of two sizes, ϕ = 0.5 and 1.0 mm, were analysed at 50 days of hydration. It was shown that within the spatial resolution of the measured μCTs, ~2 μm, the water capillary porosity was segmented within the hydrated component fraction. The unhydrated part could be accurately quantified within 2 vol% error. This work is a first step to accurately determining selected hydration features like the hydration degree of amorphous phases of supplementary cementitious materials within cement blends.