Somsubhro Chaudhuri

Dr. Somsubhro Chaudhuri

Ghent University

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 September 2020 in Materials
Verified
Journal Article
Open access
PDF file
ADAndries Daem
Andries Daem
PSPeter Sergeant
Peter Sergeant
LDLuc Dupré
Luc Dupré
SCSomsubhro Chaudhuri
Somsubhro Chaudhuri
VBVitaliy Bliznuk
Vitaliy Bliznuk
LKLeo Kestens
Leo Kestens
The energy efficiency of electric machines can be improved by optimizing their manufacturing process. During the manufacturing of ferromagnetic cores, silicon steel sheets are cut and stacked. This process introduces large stresses near cutting edges. The steel near cutting edges is in a plastically deformed stress state without external mechanical load. The magnetic properties of the steel in this stress state are investigated using a custom magnetomechanical measurement setup, stress strain measurements, electrical resistance measurements, and transmission electron microscopic (TEM) measurements. Analysis of the core energy losses is done by means of the loss separation technique. The silicon steel used in this paper is non-grain oriented (NGO) steel grade M270-35A. Three differently cut sets of M270-35A are investigated, which differ in the direction they are cut with respect to the rolling direction. The effect of sample deformation was measured—both before and after mechanical load release—on the magnetization curve and total core energy losses. It is known that the magnetic properties dramatically degrade with increasing sample deformation under mechanical load. In this paper, it was found that when the mechanical load is released, the magnetic properties degrade even further. Loss separation analysis has shown that the hysteresis loss is the main contributor to the additional core losses due to sample deformation. Releasing the mechanical load increased the hysteresis loss up to 270% at 10.4% pre-release strain. At this level of strain, the relative magnetic permeability decreased up to 45% after mechanical load release. Manufacturing processes that introduce plastic deformation are detrimental to the local magnetic material properties.

8 August 2019 in Welding in the World
Verified
Journal Article
Open access
PDF file
SCSomsubhro Chaudhuri
Somsubhro Chaudhuri
JCJ. Crump
J. Crump
PRP. A. S. Reed
P. A. S. Reed
BMB. G. Mellor
B. G. Mellor
Weld toe fatigue crack initiation is highly dependent on the local weld toe stress-concentrating geometry including any inherent flaws. These flaws are responsible for premature fatigue crack initiation (FCI) and must be minimised to maximise the fatigue life of a welded joint. In this work, a data-rich methodology has been developed to capture the true weld toe geometry and resulting local weld toe stress-field and relate this to the FCI life of a steel arc-welded joint. To obtain FCI lives, interrupted fatigue test was performed on the welded joint monitored by a novel multi-probe array of alternating current potential drop (ACPD) probes across the weld toe. This setup enabled the FCI sites to be located and the FCI life to be determined and gave an indication of early fatigue crack propagation rates. To understand fully the local weld toe stress-field, high-resolution (5 μm) 3D linear-elastic finite element (FE) models were generated from X-ray micro-computed tomography (μ-CT) of each weld toe after fatigue testing. From these models, approximately 202 stress concentration factors (SCFs) were computed for every 1 mm of weld toe. These two novel methodologies successfully link to provide an assessment of the weld quality and this is correlated with the fatigue performance.

1 May 2025 in Engineering Failure Analysis
Verified
Journal Article
Closed access
SES.A. Elahi
S.A. Elahi
FSF. Mehri Sofiani
F. Mehri Sofiani
SCSomsubhro Chaudhuri
Somsubhro Chaudhuri
JBJ.A. Balbín
J.A. Balbín
NLN.O. Larrosa
N.O. Larrosa
WWW. De Waele
W. De Waele


23 May 2022 in Fatigue & Fracture of Engineering Materials & Structures
Verified
Journal Article
Closed access
KHKris Hectors
Kris Hectors
SCSomsubhro Chaudhuri
Somsubhro Chaudhuri
Wim De WaeleWim De Waele
Wim De Waele