Sunisa Suchat

Prof. Dr. Sunisa Suchat

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 March 2021 in Polymers
Verified
Journal Article
Open access
PDF file
JIJutharat Intapun
Jutharat Intapun
TRThipsuda Rungruang
Thipsuda Rungruang
SSSunisa Suchat
Sunisa Suchat
BCBanyat Cherdchim
Banyat Cherdchim
Salim HizirogluSalim Hiziroglu
Salim Hiziroglu
The objective of this work was to investigate the influences of Klason lignin as a filler on the thermal stability and properties of natural rubber composites. The modulus and tensile strength of stabilized vulcanizates were measured before and after thermo-oxidative aging. It was determined that lignin filled natural rubber had significantly enhanced thermo-oxidative aging and mechanical properties compared to those of controlled samples. The reinforcement effect of lignin increased stress with lignin loading but it decreased at 20 phr, suggesting that the reinforcement mechanism of lignin was via strain-induced crystallization. The composite samples with 10 phr filler loading had the highest mechanical properties as well as thermo-oxidative degradation resistance. Such a finding could be due to interactions between the Klason lignin filler and natural rubber matrix. Based on the findings in this work, the degradation temperature of Klason lignin occurred at 420 °C. The absorption peaks at wavenumbers 1192 and 1374 cm−1 indicated that C–O stretching vibrations of the syringyl and guaiacyl rings of hardwood lignin existed. It was also found that the Klason lignin–rubber composite containing 10 phr had the highest stress–strain, 100% modulus, and tensile strength, while lignin showed increasing aging resistance of the composite comparable with commercial antioxidant at 1.5 phr. It appears that Klason lignin from rubberwood could be used as a green antioxidant and alternative reinforcing filler and for high performance eco-friendly natural rubber biocomposites.

1 February 2013 in Industrial Crops and Products
Verified
Journal Article
Closed access
SSSunisa Suchat
Sunisa Suchat
DPDaniel Pioch
Daniel Pioch
SPSerge Palu
Serge Palu
ETEric Tardan
Eric Tardan
ELEibertus Nicolaas Van Loo
Eibertus Nicolaas Van Loo
FDFabrice Davrieux
Fabrice Davrieux

1 December 2015 in Industrial Crops and Products
Verified
Journal Article
Closed access
SSSunisa Suchat
Sunisa Suchat
PTParichat Theanjumpol
Parichat Theanjumpol
SKSeppo Karrila
Seppo Karrila

10 January 2020 in Advances in Polymer Technology
Verified
Journal Article
Open access
PDF file
ALAunnuda Lanna
Aunnuda Lanna
MSMontri Suklueng
Montri Suklueng
CKChainuson Kasagepongsan
Chainuson Kasagepongsan
SSSunisa Suchat
Sunisa Suchat
Performance of new engineered material from epoxy resins with modified epoxidized natural rubber (ENR) and nanofillers were investigated. ENR from renewable natural crop resources is a type of green material with potential to partially substitute or replace and toughen petrochemical-based polymers. Nanocomposites (epoxy resin/ENR/fillers nanoparticles) were characterized with Fourier transform infrared spectroscopy (FTIR), dynamic light scattering (DLS), atomic force microscope (AFM), and scanning electron microscopy (SEM). Comparison of characterized and mechanical properties of nanofiller reinforced with both nanocellulose and nanosilica were studied. The nanocomposites were characterized for their mechanical properties (e.g., impact strength, tensile strength) and thermal degradation behaviour by thermal gravimetric analysis (TGA). Mechanical property investigation results show that, the impact strength of nanocomposites, can be improved by blending in ENR 50 mixed with nanofiller, relative to the baseline nanocomposite mixers. The nanofiller loading in epoxy composite showed the highest improvement in mechanical properties at 0.75 phr (parts per hundred of resin). Effects of accelerated weathering aging were evaluated, and the observed changes were larger with nanosilica than with nanocellulose filler. Here, the accelerated aging increase in tensile properties was found to be 10% after 14 days in both nanofillers, while the other mechanical properties did not change significantly. These nanocomposites are expected to have high wear rates limiting their service life.

5 June 2020 in Polymers
Verified
Journal Article
Open access
PDF file
SSSunisa Suchat
Sunisa Suchat
ALAunnuda Lanna
Aunnuda Lanna
Aujchariya ChotikhunAujchariya Chotikhun
Aujchariya Chotikhun
Salim HizirogluSalim Hiziroglu
Salim Hiziroglu
The objective of this study was to investigate the basic properties of composite materials that were made from epoxidized natural rubber and nanosilica to be used as blades for drones. Nanocomposite samples were prepared with 5% of epoxidized natural rubber and epoxy resin loaded with 3% nanosilica. Their resistance against accelerated weathering conditions as well as mechanical properties, including flexural strength, impact strength, and hardness, were evaluated. Based on the findings of this work, the impact strength of the samples decreased 13.33% and 33.33% as a result of exposing them to weathering by UV radiation for 168 h and 336 h, respectively. However, their tensile strength properties enhanced 35.71% and 19.05% for the above corresponding exposure time spars. Experimental composite samples that were made in this study would have great potential to be used as raw material for propeller blade for drones based on their properties evaluated within the scope of this work.

25 June 2025 in Industrial Crops and Products
Verified
Journal Article
Open access
KPKanokwan Phraeksong
Kanokwan Phraeksong
SBSiwarote Boonrasri
Siwarote Boonrasri
SSSunisa Suchat
Sunisa Suchat