Takao Kameda

Dr. Takao Kameda

Sankogosei(Japan), Toyama, Japan

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 November 2022 in Gels
Verified
Journal Article
Open access
PDF file
SMSayaka Miura
Sayaka Miura
RYRio Yamagishi
Rio Yamagishi
RMRiku Miyazaki
Riku Miyazaki
KYKaori Yasuda
Kaori Yasuda
YKYuki Kawano
Yuki Kawano
Satoshi TakeiSatoshi Takei
Satoshi Takei
Hydrolyzed hyaluronic acid high-resolution fine microneedles of 13 µm in diameter and 24 µm in height were fabricated from hydrolyzed hyaluronic acid gels made in mixtures of water using vacuum environment imprint lithography processes with a water permeable mold. The gas traps of water and volatile solvents in the imprint materials cause transfer failure in the conventional water impermeable molds of quartz and metal. However, the water permeable mold allows the use of 67 wt% dilution water with high solubility to increase the fluidity of the hydrolyzed hyaluronic acid during the patterning of high-resolution fine microneedles for cosmetics and pharmaceuticals. This demonstration sets a new paradigm of functional pure gels for high-resolution nano-patterning applications with various cosmetic and pharmaceutical materials containing dilution water using a water permeable mold.

9 August 2022 in Polymers
Verified
Journal Article
Open access
PDF file
WTWataru Takarada
Wataru Takarada
MBMohammad. A. Barique
Mohammad. A. Barique
TKTatsuma Kunimitsu
Tatsuma Kunimitsu
TKTakao Kameda
Takao Kameda
TKTakeshi Kikutani
Takeshi Kikutani
A ‘model’ material of recycled polypropylene (PP) was prepared through the injection molding process, and the effect of processing history on the polymer characteristics was investigated through the high-speed melt spinning of virgin and recycled PP. On-line measurement of the thinning behavior of the spin-line revealed the downstream shift of solidification point for the recycled PP at the take-up velocity of 1.0 km/min, indicating the suppression of flow-induced crystallization. The difference was not clear at higher take-up velocities of up to 5 km/min. For any identical take-up velocity, no clear difference in the stress-strain curves and birefringence of the fibers from virgin and recycled PP could be observed, whereas the detailed investigation on the variation of relative amount of c-axis and a*-axis oriented crystals in the fibers prepared at varied take-up velocities suggested the deterioration of flow-induced crystallization at 1.0 km/min. It was speculated that the processing history induced the lowering of the entanglement density, which affected the melt spinning and crystallization behavior. An undistinguishable difference between the virgin and recycled PP at increased take-up velocities suggested the existence of an optimum elongational strain rate for the detection of the different states of molecular entanglement.

5 August 2024 in Macromol
Verified
Journal Article
Open access
PDF file
MAMano Ando
Mano Ando
YHYuna Hachikubo
Yuna Hachikubo
SMSayaka Miura
Sayaka Miura
RYRio Yamagishi
Rio Yamagishi
NSNaoto Sugino
Naoto Sugino
Satoshi TakeiSatoshi Takei
Satoshi Takei
We attempted to perform surface microfabrication of the bioabsorbable material lactic acid–glycolic acid copolymer (LG-80) using a micro-imprint lithography technique with a gas-permeable porous mold at less than 5 °C. As a result, high-resolution surface micromachining with a height of 1.26 μm and a pitch of 2.97 μm was achieved using a convex sapphire mold with a height of 1.3 μm and a pitch of 3 μm. After processing, the LG-80 exhibited high water repellency, and FT-IR analysis of the surface showed no significant change in its chemical structure, confirming that the surface microfabrication was successful, while retaining the properties of the material. This demonstrated new possibilities for surface microfabrication technology for bioabsorbable materials, which are expected to be applied in the medical and life science fields in products such as surgical implants, tissue regeneration materials, and cell culture scaffold materials. In particular, the use of micro-imprint lithography enables low-cost and high-precision processing, which will be a major step toward the practical application of bioabsorbable materials.

1 January 2019
Verified
Conference Paper
Closed access
PDF file
TKTakao Kameda
Takao Kameda
STSatoshi Takei
Satoshi Takei
KYKaori Yasuda
Kaori Yasuda
NSNaoto Sugino
Naoto Sugino
Applications to photo nanoimprint lithography using gas permeable metal plates have been reported due to reduced pattern defects, air trapping problems, and template damage by gases such as nitrogen and oxygen generated from UV cross-linked materials.