Teresa Leonor Martins Morgado

Prof. Dr. Teresa Leonor Martins Morgado

Mechanical Department, Polytechnic University of Lisbon, Lisbon, Lisboa, Portugal
orcid

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2008 in Engineering Failure Analysis
Verified
Journal Article
Closed access
Teresa Leonor Martins MorgadoTeresa Leonor Martins Morgado
Teresa Leonor Martins Morgado
CBC.M. Branco
C.M. Branco
VIVirgínia Infante
Virgínia Infante

1 August 2003 in Engineering Failure Analysis
Verified
Journal Article
Closed access
VIVirgínia Infante
Virgínia Infante
CBC.M. Branco
C.M. Branco
ABA.S. Brito
A.S. Brito
Teresa Leonor Martins MorgadoTeresa Leonor Martins Morgado
Teresa Leonor Martins Morgado

1 January 2016 in Procedia Structural Integrity
Verified
Journal Article
Open access
Teresa Leonor Martins MorgadoTeresa Leonor Martins Morgado
Teresa Leonor Martins Morgado
Helena V. G. NavasHelena V. G. Navas
Helena V. G. Navas
RBR. Brites
R. Brites
In this paper a wear study of innovative Ti-Ta alloys is present. Samples of Ti-30%Ta, Ti-52%Ta, were produced by laser cladding. This technology uses a high power density generated by a laser beam to melt the base material and the filler material. The interaction between the laser and the substrate is a function of the radiation absorption properties of the material and that conditions the heat flow. Laser technology allows working with high temperatures and melting powders of titanium and the alloying elements as tantalum. As this is a continuous process enables rapid cooling of the molten material and the consequent solidification. The principal importance of these innovative alloys is the low Young’s Modulus, the closest to Young´s Modulus of the bone, the biocompatibility of titanium and tantalum and consequently its applicability to biomedical industry. The wear behavior is an important factor that influences the structural integrity of materials and must be studied for innovative alloys. So in this work the micro-scale abrasive wear tests were used to characterize the wear behavior of Ti-30%Ta, Ti-52%Ta alloys. The results shows that the wear volume increases linearly as the rotation of the ball test and with the sliding distance and the analysis of the ball cratering shows that for this test there just grooving abrasion and the volume wear abrasion is higher for the highest hardness alloy

11 September 2022 in Procedia Computer Science
Verified
Journal Article
Open access
ADA.S.M.E. Dias
A.S.M.E. Dias
RAR.M.G. Antunes
R.M.G. Antunes
AAA. Abreu
A. Abreu
VAV. Anes
V. Anes
HNH.V.G. Navas
H.V.G. Navas
JCJ.M.F. Calado
J.M.F. Calado

1 December 2015 in Case Studies in Construction Materials
Verified
Journal Article
Open access
Teresa Leonor Martins MorgadoTeresa Leonor Martins Morgado
Teresa Leonor Martins Morgado
ABA. Sousa e Brito
A. Sousa e Brito
This paper presents results of a failure analysis study to characterize the damage phenomenon that occurred in prestressed steel cables of a suspension bridge. This study includes: material characterization using chemical, microstructural and hardness analysis; fractographic analysis by scanning electron microscopy (SEM); mechanical tests of the material in static tension; fatigue tests (S–N curves) and fractographic analysis of fatigue fracture surfaces. The fatigue tests were carried out in laboratory air only and in the laboratory air also but after previous exposure in tap water to simulate the working environment of the cables. Fractured surfaces of the rods were of brittle failure type and also of cup and cone type. Due to the characteristics of the work environment (close to a river) stress corrosion was also observed and it is likely oxygen embrittlement was obtained.Results from fatigue tests and fractographic study allow to the conclusion that the main cause of cable failure, which led to a collapse of the bridge, was stress corrosion cracking (SCC)

10 November 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Vitor AnesVitor Anes
Vitor Anes
Teresa Leonor Martins MorgadoTeresa Leonor Martins Morgado
Teresa Leonor Martins Morgado
António AbreuAntónio Abreu
António Abreu
João CaladoJoão Calado
João Calado
LRLuis Reis
Luis Reis
This paper proposes a qualitative model to overcome the limitations of conventional failure mode and effects analysis (FMEA), which does not consider risk mitigation capabilities when prioritizing risks. Failure to consider these capabilities can lead to unrealistic risk estimates, especially when the level of uncertainty is high. In the proposed model, the original applicability of conventional FMEA was retained along with the three conventional risk variables, namely, severity, occurrence, and detectability. In addition, a fourth variable was added to account for risk mitigation capabilities. A case study in the project selection of aircraft repairs was used to demonstrate the implementation of the model and its applicability. The results show that the inclusion of mitigation options leads to more realistic risk scenarios, suggesting that the original FMEA approach may lead to non-conservative risk estimates.