Due to significant temperature differences between the injected medium and in situ formation, injection of CO2 (as with water or other cold fluids) at depth induces thermal changes that must be accounted for a complete understanding of the mechanical integrity of the injection/storage system. Based on evaluations for the Northern Lights Carbon Capture and Storage (CCS) project, we focus on thermal effects induced on the caprock via conduction from cooling in the storage sands below. We investigate, using both analytical and numerical approaches, how undrained effects within the low permeability caprock can lead to volumetric contraction differences between the rock framework and the pore fluid which induce both stress and pore pressure changes that must be properly quantified. We show that such undrained effects, while inducing a more complicated response in the stress changes in the caprock, do not necessarily lead to unfavourable tensile conditions, and may, in fact, lead to increases in effective stress. These observations build confidence in the integrity of the caprock/seal system. We also show, through conservative assumptions, that pressure communication between the caprock and storage sands may lead to a localised negative effective stress condition, challenging stability of the base caprock, which will be mitigated for in field development planning.
1 September 2018 in International Journal of Greenhouse Gas Control
Models of reduced dimensionality have been found to be particularly attractive in simulating the fate of injected CO2 in supercritical state in the context of carbon capture and storage. This is motivated by the confluence of three aspects: the strong buoyant segregation of the lighter CO2 phase above water, the relatively long time scales associated with storage, and finally the large aspect ratios that characterize the geometry of typical storage aquifers. However, to date, these models have been confined to considering only the flow problem, as the coupling between reduced dimensionality models for flow and models for geomechanical response has previously not been developed. Herein, we develop a fully coupled, reduced dimension, model for multiphase flow and geomechanics. It is characterized by the aquifer(s) being of lower dimension(s), while the surrounding overburden and underburden being of full dimension. The model allows for general constitutive functions for fluid flow (relative permeability and capillary pressure) and uses the standard Biot coupling between the flow and mechanical equations. The coupled model retains all the simplicities of reduced‐dimensional models for flow, including less stiff nonlinear systems of equations (since the upscaled constitutive functions are closer to linear), longer time steps (since the high grid resolution in the vertical direction can be avoided), and less degrees of freedom. We illustrate the applicability of the new coupled model through both a validation study and a practical computational example.
Assessing fault zones as fluid-migration pathways requires the characterization of permeability both across and along faults, as well as the adjacent volume. The hydraulic properties of the Vette Fault Zone, North Sea, are described by modelling the mixing of host-rock lithologies into the fault zone, and the fault width is derived from empirical relationships as a function of throw and clay content. To better understand the sensitivity related to the uncertainties in overburden lithologies and fault-width correlations, a parametric study with 1125 model realizations were solved in a 2D steady-state, single-phase, subsurface flow model. The fault zone, included as a discrete permeable structure, significantly alters the flow field compared to a model that only considers lithological juxtaposition. The most prominent hydraulic communication in the Vette Fault Zone is downwards from the storage reservoir where sand is mixed into the fault zone. Increasing the host-rock permeability in the overburden also increases the fault permeability and shifts the inflection point for down-fault flow, causing the pressurized reservoir to drain towards the overburden and the top surface. For CO 2 storage application, the models highlighted the potential for downward communication along the fault for brine, and the CO 2 capillary sealing towards the overburden. Thematic collection: This article is part of the Fault and top seals 2022 collection available at: www.lyellcollection.org/topic/collections/fault-and-top-seals-2022
10 July 2020 in Journal of Geophysical Research: Solid Earth
Fracture stiffness and flow properties have been measured in the laboratory using naturally fractured fault rock samples from the Little Grand Wash fault, Utah, USA. We compare fracture closure and related flow change during isotropic loading of two fractures which have been subject to various amounts of paleoreactive flow. The two tested fractures are described as (i) a small‐aperture fracture (0.1 mm) with negligible geochemical alterations of the fracture surface and (ii) a large‐aperture fracture (0.53 mm) where precipitates are observed on the fracture surface. X‐ray imaging is used for quantification of fracture aperture and fracture surface contact distribution. The petrographical characterization using scanning electron microscopy and X‐ray powder diffraction is performed pretest and describes burial and uplift diagenesis as well as pulses of reactive fluid flow within the fault. The stress‐dependent flow and deformation experiment provides new data on fracture stiffness and flow for naturally developed fractures in siliciclastic rock. Fracture stiffness is found to be highest for the small‐aperture fracture due to its high‐fracture contact ratio and well‐developed surface mating during closure. For the naturally altered and rougher, large‐aperture fracture, fracture stiffness is lower and a highly stress dependent decay in flow is observed during initial closure. The results illustrate that a natural fracture with high contact ratio and well‐mated surfaces will close during loading, whereas a fracture associated with high flow rates and affected by previous geochemical alteration maintains a high flow rate compared to the host rock during similar loading.