VICTOR LOPEZ GARZA

Dr. VICTOR LOPEZ GARZA

FACULTY OF MECHANICAL ENGINEERING, Universidad Michoacana de San Nicolás de Hidalgo, Morelia, Michoacán de Ocampo, Mexico
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2019 in Advances in Engineering Software
Verified
Journal Article
Closed access
ITIshvari F. Zuñiga Tello
Ishvari F. Zuñiga Tello
GAGonzalo M. Dominguez Almaraz
Gonzalo M. Dominguez Almaraz
VICTOR LOPEZ GARZAVICTOR LOPEZ GARZA
VICTOR LOPEZ GARZA
MTManuel Guzmán Tapia
Manuel Guzmán Tapia

25 January 2025 in Energies
Verified
Journal Article
Open access
PDF file
MVMiriam Vázquez
Miriam Vázquez
VICTOR LOPEZ GARZAVICTOR LOPEZ GARZA
VICTOR LOPEZ GARZA
Rafael Campos AmezcuaRafael Campos Amezcua
Rafael Campos Amezcua
Erasmo CadenasErasmo Cadenas
Erasmo Cadenas
PMPaulina Marin-Tellez
Paulina Marin-Tellez
IEC 61400-2 establishes the Simplified Load Method for designing low-power wind turbine blades without considering dynamic loads in the simplified load methodology. This paper analyzes the load hypotheses established by the standard, also considering the natural frequencies in a 900 W blade. The research methodology begins with the design parameters, the application of the BEM Method, and the use of the QBlade software. Then, the load hypotheses of the standard are defined. Finally, the structural design and the modal and structural analysis of the blade were conducted using FEM-based software. The results show that the minimum participation factors are found on the z-axis and the maximum on the x- and y-axis, and their magnitudes decrease when the natural frequency increases. In general, the principal maximum stresses are located in the middle section of the blade, in the external fiberglass layer, both on the intrados and extrados sides. In conclusion, structural scenarios were established to relate the participation factors of the modal analyses with the load hypotheses. The critical scenarios are at natural frequencies below 280 Hz.

31 March 2019 in Revista de Simulación y Laboratorio
Verified
Journal Article
Open access
PMPaulina Marin-Tellez
Paulina Marin-Tellez
VICTOR LOPEZ GARZAVICTOR LOPEZ GARZA
VICTOR LOPEZ GARZA
EPErick Pérez-Juárez
Erick Pérez-Juárez
GGGilberto Gonzalez
Gilberto Gonzalez
In the present work is shown the numerical simulation performed by means of finite element software (FEA) and the static mechanical tests using extensometric techniques for a wind turbine blade of 600W in accordance with the international standard IEC 61400-2. A NACA 4412 profile was used and the loads applied were selected according to the following load hypotheses described in the standard: normal operation, maximum thrust, immobilization with wind load and maximum exposure. A methodology was developed for both the simulation and for the laboratory tests, the data of the microdeformation measured by extensometry were also analyzed and compared with those obtained by the numerical simulation. Concluding that the analysis of finite elements is a key step prior to manufacturing that allows us to save resources and gives us parameters to perform both manufacturing and testing. Laboratory tests are necessary to ensure safe and reliable functioning of the blade during its useful life.

30 September 2019 in Revista de Ingeniería Mecánica
Verified
Journal Article
Open access
MRMartín Romero-Franco
Martín Romero-Franco
VICTOR LOPEZ GARZAVICTOR LOPEZ GARZA
VICTOR LOPEZ GARZA
PMPaulina Marin-Tellez
Paulina Marin-Tellez
EPErik Pérez-Juárez
Erik Pérez-Juárez
In the present work, it is shows the design, manufacture and mechanical tests of a load cell for application in a turbine test bench of low capacity wind turbines are shown. The test bench is designed to withstand loads up to 3000 Nw and vanes up to 2.5 m in length. The general methodology of the cell design consists of, first, determining the operating loads of the bank, the selection of the type of load cell, the manufacture of this, the selection of the strain gauges for the measurement, the placement of the strain gauges in the load cell and finally the mechanical tests of the cell in the test bench. The material of the cell is aluminum 6061 and the conFiguration is type "S". As conclusions, it is mentioned that extensometric techniques allow to characterize the load cell by means of laboratory tests fulfilling the desired specifications with the design.

30 June 2020 in Revista del Diseño Innovativo
Verified
Journal Article
Open access
JCJosé Luis Colín-Martínez
José Luis Colín-Martínez
VICTOR LOPEZ GARZAVICTOR LOPEZ GARZA
VICTOR LOPEZ GARZA
IHIsaac Hernández-Arriaga
Isaac Hernández-Arriaga
MRMaria Guadalupe Navarro Rojero
Maria Guadalupe Navarro Rojero
Currently, wind energy in Mexico is growing and the same is happening worldwide, so projects with national technologies for the manufacture of wind turbine components must be developed. In this work, a proposal is made for the design of the hub of the rotor for a 50-kW turbine, the objective is to make a new proposal to improve the previous design of project P07 of the Centro Mexicano de Innovación en Energía Eólica (CEMIEEólico), which has a welded mechanical hub for a prototype turbine 30 kW. In addition, a simulation is performed through analysis of the finite element method (FEA) by applying certain load elements with the simplified load method of the international standard IEC 61400-2. In these simulations, the load cases of the norm that directly influence the cube are analyzed, then simulated in the ANSYS software to validate the proposed design, mainly analyzing the stresses and deformations. The results obtained will serve as a reference to manufacture the cube and evaluate the feasibility of carrying out a commercial stage with a view to making national components for wind farms.

23 October 2024 in Revista Ingeniería
Verified
Journal Article
Open access
PDF file
JMJosé Luis Colín Martínez
José Luis Colín Martínez
VICTOR LOPEZ GARZAVICTOR LOPEZ GARZA
VICTOR LOPEZ GARZA
GHGuillermo Muñoz Hernández
Guillermo Muñoz Hernández
La sostenibilidad y el impacto ambiental de las energías renovables es objeto de una creciente preocupación que, ha llevado a un enfoque renovado en el reciclaje de componentes de aerogeneradores, particularmente las aspas. El objetivo es analizar los métodos de reciclaje enfocado a las aspas de aerogeneradores en México. El enfoque es mixto, combinando métodos cualitativos como cuantitativos. Para recoger la información se utilizó la revisión documental y un análisis de la literatura sobre aspas de aerogeneradores. Los resultados muestran que, a medida que la energía eólica crece como una fuente de energía renovable, la gestión adecuada de los residuos generados por las palas que, se convierte en un aspecto crítico para asegurar la sostenibilidad del sector. Se concluye que, para alcanzar una gestión sostenible y eficiente de estos residuos, es fundamental explorar métodos físicos como la trituración mecánica. Este enfoque no solo reduce costos de transporte, sino que también facilita el manejo en sitios especializados cercanos a los centros de uso de productos de fibra de vidrio.