Metal additive manufacturing (AM) technologies can be classified according to the physical process involving the raw material as fusion-based and solid-state processes. The latter includes sintering-based technologies, which are aligned with conventional fabrication techniques, such as metal injection molding (MIM), and take advantage of the freeform fabrication of the initial green part. In the present work, 17-4PH stainless steel samples were fabricated by material extrusion, or rather bound metal deposition (BMD), a solid-state AM technology. The powder-based raw material was characterized together with samples fabricated using different angular infill strategies. By coupling different characterization technologies, it was possible to identify and classify major properties and defects of the raw material and the fabricated samples. In addition, microstructural modifications were found to be linked with the mesostructural defects typical of the BMD solid-state additive manufacturing technology applied to metals.
23 July 2020 in The International Journal of Advanced Manufacturing Technology
The present work aims at studying the effect of geometric parameters of isogrid structures on their buckling behavior. To this purpose, isogrid structures in polyamide reinforced with short carbon fibers, with different rib widths, rib thicknesses, and cell heights, were additively manufactured using the fused deposition modeling technology; then, they were subjected to compression test until the occurrence of buckling. It was observed that isogrid structures can undergo to different failure modes, local and global buckling, depending on the values of geometrical parameters. Furthermore, the geometrical parameters that lead to the highest strength are different to those providing the highest specific strength. However, the specific strength of the 3D printed composite material is higher than those of 1XXX and 3XXX aluminum alloys. Rib thickness was characterized by the highest effect on both strength and specific strength while the cell height results in the lowest contribution. Finally, optical and scanning electron microscopies were carried out in order to analyze the fractured ribs and to obtain high magnification three-dimensional topography of fractured surfaces after buckling. The effect of moisture content on polyamide reinforced composites and the comparison between 3D printed and traditionally produced isogrid structures will be investigated in future researches.
The creep response of the 17-4PH precipitation hardening steel produced by a new additive manufacturing technology (Bound Metal Deposition) was investigated at 482 °C (900 °F), under stresses ranging from 350 to 600 MPa. Two different sets of samples produced with different deposition parameters were considered. Prior heat treatment consisted of ageing either at 482 °C (state H900) or at 621 °C (H1150). The minimum creep rate and time to rupture dependencies on applied stress were obtained. The creep response in terms of time to rupture under a given stress, in particular, was compared with the only other available literature dataset on a similar steel processed by traditional technologies. The analysis of the experiments demonstrated that the presence of dispersed defects causes, in the Bound Metal Deposited steel, a substantial reduction (35–40%) of the creep strength.
Friction stir welding (FSW) has now reached a technological impact and diffusion that makes it a common joining practice for several classes of metallic materials. These include light alloys (aluminum, titanium, magnesium), steels, and other metallic alloys. In addition, the combination of FSW with pre- or post-welding heat treatments or plastic deformation, such as cold rolling (CR), can favor minimal necessary plate thicknesses and induce effective alloy strengthening mechanisms that make the FSW joint lines as plate reinforcing zones. Process parameters, such as pin rotation and transverse speed, can be tuned to optimize the mechanical properties of the resulting joint. This work presents a microstructural study of the mechanical response of different sequences of heat treatment, FSW, and CR in a non-age hardened Al-Mg AA5754 alloy. By using polarized optical microscopy and microhardness tests, two FSW conditions were used to fabricate a joint; and were than subjected to different sequences of heat treatment and cold rolling. The results suggest that FSW conditions have a limited effect on the microstructure, while microhardness profiles show a higher variability of the different datasets related to the low welding speed investigated.
1 March 2025 in Progress in Additive Manufacturing
The microstructure and mechanical properties of metallic parts produced by additive manufacturing are significantly influenced by processing parameters. For laser-based technologies, the laser beam shape introduces an additional variable, which can profoundly affect the crystallography orientation, microstructure, and phase composition of the final part. This study investigates the effects of a Gaussian laser beam profile on the microstructure and phase distribution in thin-walled 316L stainless steel samples fabricated by directed energy deposition (DED). Hollow cylinders fabricated with a single-bead deposition were cut in one position along the growth direction (YZ sample). Furthermore, additional cuts were performed in positions perpendicular to the building direction in order to extract two XY samples, one comprising the first deposited layers and the second one the final layers of the build job. Detailed characterization revealed that the Gaussian beam shape profile drives localized variations in phase composition, with a marked disparity in δ-ferrite content between the outer regions and the core of the walls. Furthermore, microhardness measurements along the printing direction indicate that lattice microstrain, rather than primary cellular arm spacing (PCAS), predominantly governs hardness levels.