Vikas Singh Bhadoria

Dr. Vikas Singh Bhadoria

ABES Engineering College, Ghaziabad, India
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 August 2023 in IEEE Access
Verified
Journal Article
Open access
DYDilip Yadav
Dilip Yadav
NSNidhi Singh
Nidhi Singh
VBVikas Singh Bhadoria
Vikas Singh Bhadoria
VVVasiliki Vita
Vasiliki Vita
Georgios FotisGeorgios Fotis
Georgios Fotis
TMTheodoros I. Maris
Theodoros I. Maris
This paper presents a comparative analysis of single, double, and three-diode models for commercial and industrial photovoltaic (PV) cells. The efficiency of a PV system depends on various factors, including fill factor, material effect, temperature coefficient, interconnections, module degradation, solar irradiation, module temperature, soiling, potential induced degradation, PV module tilt angle, parasitic resistance, and shading effect. The results show that adding diodes decreases the maximum allowable power taken from a PV cell, resulting in the single-diode model with the highest efficiency of 99.9% at STC. As the temperature increases, the voltage decreases and the maximum power decreases to 4.044 watts/°C, while with the rise in irradiation, the maximum power value increases to 80.04 watts/100w/m 2 . A rise in temperature affects voltage and current values, while irradiation affects current values. An increase in series resistance decreases maximum power values by 216.785 watts/0.1-ohm, while shunt resistance increases maximum power by 0.0725 watts/100 ohm without significant change in current value. Pmax , Vmax , and Imax values increase with a decrease in shading value. Two and three-diodes respond more effectively than single diodes at the lowest and maximum shading values. Total-Cross-Tied configurations perform more efficiently in various connections, while HC and BL connections have comparable I-V performance. However, BL and HC have low maximum power. MATLAB software is used for modeling and simulation, assisting researchers in understanding factors affecting solar PV system efficiency and diode models.

3 February 2023 in IEEE Access
Verified
Journal Article
Open access
RYRavindra Kumar Yadav
Ravindra Kumar Yadav
PHP. N. Hrisheekesha
P. N. Hrisheekesha
VBVikas Singh Bhadoria
Vikas Singh Bhadoria
Most of world’s energy demand is fulfilled by natural resources (Oil, Coal, Gas, etc.) and there is a huge gap between demand and supply. Therefore, utilities are facing the problem of peak load burden. Broadly speaking, to sustain future electricity demand renewable/alternate sources (solar, wind etc.) of energy must be integrated with a smart grid (SG) to cope with energy demand. These sources are freely available, inexhaustible and can be used as an alternate source of energy. For smart utilization of electrical energy, a balance between supply and demand is required at all instants of time. In the SG environment, the most promising solution to reduce the peak load burden on utility is demand side management (DSM) which is possible because of the property of smart grid inertia. DSM permits all types of consumers to alter their energy consumption pattern to reduce the cost of energy and it helps the utility to reduce peak load burden and reshape load profile. In this study, DSM has been formulated as a single objective minimization problem to reduce peak load burden on utility. Although several optimization techniques has been listed in the literature which reduces the peak load and cost of energy, but integration of renewable energy is limited to residential consumers only. In this paper, a robust optimization algorithm inspired by the lifestyle of grey wolves, popularly known as grey wolf optimization (GWO) algorithm is utilized to solve the proposed DSM minimization problem. The DSM minimization problem optimization using GWO is demonstrated on three different cases-residential, commercial, and industrial loads in time of use (TOU) pricing scheme with and without solar PV energy (SPVE). Validation of GWO displays remarkable reductions in peak load on utility and cost of energy of consumers with and without SPVE. The paper incorporates the benefits of integration of solar PV systems with smart grids in the application of in three different areas considered in the study. Also, GWO optimization results are compared with existing research papers having identical data sets.

1 December 2022 in Energies
Verified
Journal Article
Open access
PDF file
SSShilpa Sambhi
Shilpa Sambhi
HSHimanshu Sharma
Himanshu Sharma
VBVikas Singh Bhadoria
Vikas Singh Bhadoria
PKPankaj Kumar
Pankaj Kumar
RCRavi Chaurasia
Ravi Chaurasia
CPChristos Pavlatos
Christos Pavlatos
This paper mainly dealt with the technical and economic feasibility of an off-grid hybrid power generation system for a remote rural Turtuk village of Ladakh, located in the northern part of India. The study showed that the proposed configured renewable integrated hybrid system, using Hybrid Optimization of Multiple Energy Resources (HOMER) software, efficiently met the energy demand, exhibiting optimum performance with low investment. The proposed PV(115 kW)/Wind(1 kW)/Battery(164 strings of 6 V each)/DG(50 kW) hybrid system was a highly commendable, feasible solution preferred from a total of 133,156 available solutions resulting from HOMER simulations. The net present cost and energy cost of the proposed configuration were $278,176 and $0.29/kWh, respectively. The proposed hybrid configuration fulfilled local load, with 95.97% reduced dominant harmful carbon dioxide emission, as compared to the sole us of a diesel generator power supply system. The technical performance of the hybrid system was ensured, with advantages including the highest renewable penetration and least unmet load. Furthermore, the analysis exclusively evaluated the impact of the system’s economic parameters (namely, its expected inflation rate, nominal discount rate, and project lifetime) on the net present cost and cost of energy of the system using a noble single fix duo vary approach.

1 December 2020 in IEEE Access
Verified
Journal Article
Open access
VBVikas Singh Bhadoria
Vikas Singh Bhadoria
RPRupendra Kumar Pachauri
Rupendra Kumar Pachauri
STShubham Tiwari
Shubham Tiwari
SJShiva Pujan Jaiswal
Shiva Pujan Jaiswal
Hassan Haes AlhelouHassan Haes Alhelou
Hassan Haes Alhelou
This paper investigates the electrical performance of serial - parallel (SP) electric connections under artificial arrangement for partial shading conditions (PSCs) in a photovoltaic (PV) array. The concept of bypass diode (BPD) is a very attractive solution to reduce the shading effect on the PV module and therefore gives better performance in such shading environment types. Various bypass diode integration (BPD) placement topologies with the solar photovoltaic (PV) modules are being investigated to demonstrate the improved performance under PSTCs in the current work. The seventeen PV modules arranged in SP configuration are associated with the BPD Topologies such as (a) W–BPD (b), SS–SBPD (c) SS–DBPD (d) Series G–BPD (e) SG–BPD (f) ML–OBPD for performance investigation. The performance assessment for all PV array supported by BPD topologies has been investigated using current –voltage (I –V) and power –voltage (P –V) characteristics and comparing to show better power and voltage results at global maximum power point (GMPP), improved fill factor and minimized power losses etc. The results presented may be recommended for the appropriate PV array configuration interconnection of BPD. Overall, this article reports that the ML–OBPD based SP configured PV array is superior among the BPD topologies under the considered PSTCs.

19 January 2024 in IEEE Access
Verified
Journal Article
Open access
SDSoma Deb
Soma Deb
SLSuman Lata
Suman Lata
VBVikas Singh Bhadoria
Vikas Singh Bhadoria
STShubham Tiwari
Shubham Tiwari
TMTheodoros I. Maris
Theodoros I. Maris
Georgios FotisGeorgios Fotis
Georgios Fotis
Based on the signum function (sign of magnitudes) of transient energy, this paper proposes a fault classification approach and algorithm for a monopolar HVDC system. The analytical study here shows that the signum function of variation in transient energy has a zero value individually at both ends on no-fault conditions. Moreover, the summation of the signum functions computed for internal DC faults is zero, whereas the same has a non-zero value for external AC faults. The performance of the proposed algorithm has been extensively evaluated by simulating faults on a CIGRE benchmark system for HVDC monopolar configuration using EMTDC/PSCAD software. Three locations of DC line fault, and AC fault at the two ends of the system have been considered for this evaluation. Five fault resistance values (0, 10, 100, 1000, and 2000 ohms) have been simulated for each fault location. The results conform with the theoretical analysis, and the fault classification by the algorithm is 100% accurate. The time taken to detect and classify a DC fault at the mid-point of the 800-km line is 1.5 ms, and that for line-end faults on the DC line is 3 ms for all values of fault resistance. These results show a marked improvement over those reported earlier in the literature using other techniques. A comparison table is given in the last section to corroborate it.

26 July 2021 in IEEE Access
Verified
Journal Article
Open access
AGArunprasad Govindharaj
Arunprasad Govindharaj
AMAnitha Mariappan
Anitha Mariappan
AAA Ambikapthy
A Ambikapthy
VBVikas Singh Bhadoria
Vikas Singh Bhadoria
Hassan Haes AlhelouHassan Haes Alhelou
Hassan Haes Alhelou
The efficiency of the low-cost renewable energy source i.e. solar is very poor due to inadequate extraction of maximum power. By employing the proper maximum power point tracking algorithm, the efficiency can be increased. An innovative adaptive backstepping neural network controller is proposed in this paper to extract the maximum power from the solar panels by tracking the desired photovoltaic array voltage in real-time. The maximum power is extracted indirectly by tuning the PV voltage to the desired PV voltage where the maximum power is attained at the desired PV voltage point. The desired photovoltaic array voltage is obtained from the linear regression method. The change in photovoltaic current caused by varying irradiance and temperature is approximated using the Chebyshev polynomials. The quicker steady-state and transient responses are accomplished and the computational burden of the photovoltaic system control law is reduced because of the orthogonal property of Chebyshev polynomials. The asymptotically stable system is obtained by tuning the weights of the neurons in accordance with the Lyapunov stability analysis. Also, Lyapunov control function of the backstepping control design procedure finds a control law by an innovative cubic equation interpretation, instead of resolving the first derivative of the control law, that diminishes the ripples in the duty cycle to make its appropriateness in real-time. A prototype is developed to validate the robustness of this controller in maximum power extraction at a faster time and the results confirm that adaptive backstepping neural network controller surpasses the performances of conventional backstepping controller and constant voltage PID controller.