Van Nhuong Vu

Dr. Van Nhuong Vu

ThaiNguyen University of Education, Thái Nguyên, Vietnam
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 April 2023 in RSC Advances
Verified
Journal Article
Open access
PDF file
LTLoan N T T
Loan N T T
HNHang T. T. Nguyen
Hang T. T. Nguyen
LNLan T. H. Nguyen
Lan T. H. Nguyen
ADAnh T. T. Duong
Anh T. T. Duong
HNHai Q. Nguyen
Hai Q. Nguyen
TTThuan Tran
Thuan Tran
Doping of neodymium ions into CoFe 2 O 4 nanoparticles significantly boosted the photocatalytic activity of CoNd x Fe 2− x O 4 for the degradation of Rhodamine B dye. Up to 94.7% of dye was degraded under CoNd 0.05 Fe 1.95 O 4 /H 2 O 2 /visible-light system.

1 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
Quoc Toan TranQuoc Toan Tran
Quoc Toan Tran
DHDo Tra Huong
Do Tra Huong
XHXuan Linh Ha
Xuan Linh Ha
TDThi Tu Anh Duong
Thi Tu Anh Duong
CNChu Nhuong
Chu Nhuong
PSPhomthavongsy Song
Phomthavongsy Song
For the first time, activated carbon from a durian shell (ACDS) activated by H2SO4 was successfully synthesized in the present study. The fabricated ACDS has a porous surface with a specific surface area of 348.0017 m2·g−1, average capillary volume of 0.153518 cm3·g−1, the average pore diameter of 4.3800 nm; ash level of 55.63%; humidity of 4.74%; density of 0.83 g·cm−3; an iodine index of 634 mg·g−1; and an isoelectric point of 6.03. Several factors affecting Methylene Blue (MB) adsorption capacity of ACDS activated carbon was investigated by the static adsorption method, revealing that the adsorption equilibrium was achieved after 90 min. The best adsorbent pH for MB is 7 and the mass/volume ratio is equal to 2.5 g·L−1. The MB adsorption process of ACDS activated carbon follows the Langmuir, Freundlich, Tempkin, and Elovich isotherm adsorption model, which has determined the maximum adsorption capacity for MB of ACDS as qmax = 57.47 mg·g−1. The MB adsorption process of ACDS follows the of pseudo-second-order adsorption kinetic equation. The Weber and Morris Internal Diffusion Model, the Hameed and Daud External Diffusion Model of liquids have been studied to see if the surface phase plays any role in the adsorption process. The results of thermodynamic calculation of the adsorption process show that the adsorption process is dominated by chemical adsorption and endothermic. The obtained results provide an insight for potential applications of ACDS in the treatment of water contaminated by dyes.

23 June 2022 in Inorganics
Verified
Journal Article
Open access
PDF file
VVVan Nhuong Vu
Van Nhuong Vu
TPThi Ha Thanh Pham
Thi Ha Thanh Pham
MCMaiboun Chanthavong
Maiboun Chanthavong
DHDo Tra Huong
Do Tra Huong
LNLan T. H. Nguyen
Lan T. H. Nguyen
KTKim Ngan Tran
Kim Ngan Tran
The co-precipitation method was employed to synthesize a set of ZnAl hydrotalcite materials modified by Cu2+. The synthesized materials have a similar lamellar structure to that of hydrotalcite. The distance between layers is in the range of 7.73–8.56 Å. The network parameters a and c ranged from 3.058 to 3.074 Å and from 23.01 to 24.44, respectively. According to the IUPAC classification, the composites possess a mesoporous structure which belongs to class IV, type H 3. Particularly, the absorption edge shifts strongly to the visible light region when increasing the molar ratio of Cu2+ in the samples from 0 to 3.5. The photocatalytic activity of the synthetic materials was evaluated through the degradation efficiency of rhodamine-B (Rh-B) in the water and colorants in textile wastewater. The present study was the first to synthesize a material sample that contains a molar ratio of Cu2+ in the range of 2.5–3.5 and has high catalytic activities. They were able to degrade Rh-B at a high concentration (100 ppm) with a conversion rate of approximately 90% after 240 min of irradiation using a 30 W LED light. The catalytic activity of the composites depends on the molar ratio of modified Cu2+, the value of environmental pH, the H2O2 concentration and the irradiation time.

8 August 2022 in Processes
Verified
Journal Article
Open access
PDF file
VVVan Nhuong Vu
Van Nhuong Vu
TPThi Ha Thanh Pham
Thi Ha Thanh Pham
NDNguyen Quoc Dung
Nguyen Quoc Dung
TVThi Hau Vu
Thi Hau Vu
TDThi Tu Anh Duong
Thi Tu Anh Duong
KTKim Ngan Tran
Kim Ngan Tran
ZnAlCO3 hydrotalcite materials modified by Cu2+ ions were synthesized by the co-precipitation method according to the molar ratios of (Cu2+ + Zn2+):Al3+ as 7:3. Thus, the modified materials contain various molar ratios of Cu2+ from 0–3.5 in the samples. The synthesized materials were characterized by X-ray diffraction pattern (XRD), FT–IR, EDS, SEM, the N2 adsorption/desorption isotherm (BET), and UV–Vis DRS spectrum. The synthesized materials were characterized by a layered double hydroxide structure—such as hydrotalcite. The specific surface area BET increases slightly, corresponding to the increasing Cu2+ molar ratios, and the bandgap energy Eg decreases accordingly. Especially, these material samples have a high phenol red (PR) adsorption capacity at a concentration of 100 ppm and PR was degraded under a 30 W LED light with over 90% of conversion efficiency in the presence of 1.2 mL of 30% H2O2 solution. In addition, the CuH–3.5 material sample maintained stability after four times catalytic reuse. Therefore, this material can be used as an effective treatment for the wastewater of the sedge mat weaving village.

11 August 2025 in RSC Advances
Verified
Journal Article
Open access
PDF file
VVVan Nhuong Vu
Van Nhuong Vu
TPThi Ha Thanh Pham
Thi Ha Thanh Pham
TLThi Huong Le
Thi Huong Le
Truong Xuan VuongTruong Xuan Vuong
Truong Xuan Vuong
This study investigates Cu(II)-modified Mg–Al layered double hydroxide (LDH) composites for efficient removal of phenol red (PR) from water through adsorption and visible-light photocatalysis. The aim was to develop a sustainable material capable of addressing dye pollution in textile wastewater. The composites were synthesized via co-precipitation with optional calcination, non-calcined and calcined materials. Structural characterization (XRD, EDX, FT-IR, SEM) confirmed successful Cu2+ incorporation by isomorphic substitution, forming mesoporous, less crystalline structures. Uncalcined samples, particularly 5-CuH, retained a layered morphology and removed up to 94% of PR. The removal occurred via electrostatic attraction, π–π interactions, and ion exchange. Cu2+ narrowed the bandgap (Eg ≈ 2.1–3.1 eV), enhancing photocatalytic activity. Under visible light, 5-CuH degraded approximately 40% of PR within 60 minutes. Calcined samples (e.g., 5-CuH500) formed CuO particles and performed better under acidic conditions despite reduced structural integrity. Both materials reduced COD by over 90% in real textile wastewater, confirming their dual-function performance, adsorption and photocatalysis. In conclusion, Cu–Mg–Al composites offer an effective, eco-friendly alternative for treating dye-contaminated wastewater.

23 March 2026 in RSC Advances
Verified
Journal Article
Open access
PDF file
VVVan Nhuong Vu
Van Nhuong Vu
TPThi Ha Thanh Pham
Thi Ha Thanh Pham
TDThi Tu Anh Duong
Thi Tu Anh Duong
LTLoan N T T
Loan N T T
Truong Xuan VuongTruong Xuan Vuong
Truong Xuan Vuong
Dye pollution from textile effluents poses significant environmental challenges, necessitating efficient and sustainable treatment technologies. In this study, Cu(II)-modified Mg–Al layered double hydroxide (5CuH) and its bentonite-supported composites were synthesized via a facile co-precipitation strategy and systematically characterized by XRD, SEM, BET, EDX, and UV-Vis DRS. Structural analysis confirmed successful Cu incorporation and uniform LDH dispersion on bentonite, resulting in narrowed band gaps (1.42–2.12 eV) and enhanced visible-light responsiveness. Under visible-light irradiation, 5CuH and 5CuH/Bent-2 achieved over 90% RhB degradation within 60 min at 50 ppm, accompanied by substantial mineralization. The 5CuH catalyst maintained high stability over four cycles with only 4.7% efficiency loss, while the composite showed moderate decline due to partial Cu2+ leaching but preserved structural integrity. Both materials effectively treated real textile wastewater, reducing COD to meet QCVN 40:2025/BTNMT discharge standards. This work demonstrates a synergistic clay-LDH design strategy that enhances charge separation and reactive oxygen species generation under visible light. Unlike adsorption-dominated systems, pollutant removal is primarily governed by photocatalytic oxidation, enabling efficient degradation and mineralization in complex wastewater matrices. The combination of low-cost raw materials, simple synthesis, and strong practical performance highlights the scalability and industrial potential of clay-supported LDH photocatalysts for sustainable textile wastewater remediation.