Wim Buijs

Prof. Dr. Wim Buijs

orcid
Emeritus

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 October 2017 in Industrial & Engineering Chemistry Research
Verified
Journal Article
Open access
Wim BuijsWim Buijs
Wim Buijs
SFStijn de Flart
Stijn de Flart
Several reactions, known from other amine systems for CO2 capture, have been proposed for Lewatit R VP OC 1065. The aim of this molecular modeling study is to elucidate the CO2 capture process: the physisorption process prior to the CO2-capture and the reactions. Molecular modeling yields that the resin has a structure with benzyl amine groups on alternating positions in close vicinity of each other. Based on this structure, the preferred adsorption mode of CO2 and H2O was established. Next, using standard Density Functional Theory two catalytic reactions responsible for the actual CO2 capture were identified: direct amine and amine-H2O catalyzed formation of carbamic acid. The latter is a new type of catalysis. Other reactions are unlikely. Quantitative verification of the molecular modeling results with known experimental CO2 adsorption isotherms, applying a dual site Langmuir adsorption isotherm model, further supports all results of this molecular modeling study.

28 August 2019 in Industrial & Engineering Chemistry Research
Verified
Journal Article
Open access
Wim BuijsWim Buijs
Wim Buijs
Lewatit R VP OC 1065 is a promising material for Direct Air Capture of CO2. However it was found that serious oxidative degradation already started from 80oC. In this DFT study oxidative degradation is described as a series of well-known reactions in air-oxidation chemistry. Oxidation of the resin starts with the formation of an -benzyl amino hydroperoxide. Thermal decomposition of the -benzyl amino hydroperoxide is the second step and leads eventually to the corresponding amide (R(C=O)NH2) and the half-aminal (RCH(OH)(NH2). The half-aminal further solvolyses predominantly to an aldehyde (RCHO). Both the amide and the aldehyde are responsible for the experimentally observed loss of CO2 capacity as these groups are not able to capture CO2. Rate determining step in oxidative degradation is usually the decomposition of the hydroperoxide, but in this case the formation of the -benzyl amino hydroperoxide cannot be excluded. The apparent contradiction between the results of Hallenbeck et al., and Yu et al., with respect to the oxygen content before and after exposure of the resin to air at high temperature is explained by the difference in H2O content before and after, and oxygen incorporation by amide and aldehyde formation after exposure to air. The loss of nitrogen content on exposure to air at high temperature is explained by the formation of aldehydes.


5 July 2018 in Industrial & Engineering Chemistry Research
Verified
Journal Article
Open access
Wim BuijsWim Buijs
Wim Buijs
IHIbnelwaleed Hussein
Ibnelwaleed Hussein
MMMohamed Mahmoud
Mohamed Mahmoud
ABDULMUJEEB TOLUWASE ONAWOLEABDULMUJEEB TOLUWASE ONAWOLE
ABDULMUJEEB TOLUWASE ONAWOLE
Mohammed Ali H Saleh SaadMohammed Ali H Saleh Saad
Mohammed Ali H Saleh Saad
GBGolibjon R. Berdiyorov
Golibjon R. Berdiyorov
A common problem that faces the oil and gas industry is the formation of iron sulphide scale in various stages of production. Recently an effective chemical formulation was proposed to remove all types of iron-sulfide scales (including pyrite), consisting of a chelating agent Di-ethylene-Tri-amine-Penta-Acetic acid (DTPA) at high pH using potassium carbonate (K2CO3). The aim of this Molecular Modelling study is to develop insight into the thermodynamics and kinetics of the chemical reactions during scale removal. A cluster approach was chosen to mimic the overall system. Standard density functional theory (B3LYP/6-31G*) was used for all calculations. Low spin K4Fe(II)4(S2H)12 and K3Fe(II)(S2H)5 clusters were derived from the crystal structure of pyrite, and used as mimics for surface scale FeS2. In addition, K5DTPA was used as a starting material too. High spin K3Fe(II)DTPA, and K2S2 were considered as products. A series of Km(Fe(II)(S2H)n complexes (m= 3-1, n= 5-0) with various carboxylate and glycinate ligands was used to establish the most plausible reaction pathway. Some ligand exchange reactions were investigated on even simpler Fe(II) complexes in various spin states. It was found that the dissolution of iron sulphide scale with DTPA under basic conditions is thermodynamically favoured and not limited by ligand exchange kinetics as the activation barriers for these reactions are very low. Singlet-quintet spin crossover and aqueous solvation of the products almost equally contribute to the overall reaction energy. Furthermore seven-coordination to Fe(II) was observed both in high spin K3Fe(II)DTPA and K2Fe(II)(EDTA)(H2O) albeit in a slightly different manner.

1 March 2018 in Journal of Molecular Structure
Verified
Journal Article
Closed access
MYMiao Yu
Miao Yu
HEHayley A. Every
Hayley A. Every
WJWim Jiskoot
Wim Jiskoot
GWGeert-Jan Witkamp
Geert-Jan Witkamp
Wim BuijsWim Buijs
Wim Buijs

25 August 2017 in The Journal of Physical Chemistry B
Verified
Journal Article
Open access
SJSeyed Hossein Jamali
Seyed Hossein Jamali
MRMahinder Ramdin
Mahinder Ramdin
TBTim M. Becker
Tim M. Becker
SRShwet Kumar Rinwa
Shwet Kumar Rinwa
Wim BuijsWim Buijs
Wim Buijs
TVThijs J.H. Vlugt
Thijs J.H. Vlugt
Crown-ethers have recently been used to assemble porous liquids (PLs), which are liquids with permanent porosity formed by mixing bulky solvent molecules (e.g., 15-crown-5 ether) with solvent-inaccessible organic cages. PLs and crown-ethers belong to a novel class of materials, which can potentially be used for gas separation and storage, but their performance for this purpose needs to be assessed thoroughly. Here, we use molecular simulations to study the gas separation performance of crown-ethers as the solvent of porous liquids. The TraPPE force field for linear ether molecules has been adjusted by fitting a new set of torsional potentials to accurately describe cyclic crown-ether molecules. Molecular dynamics (MD) simulations have been used to compute densities, shear viscosities, and self-diffusion coefficients of 12-crown-4, 15-crown-5, and 18-crown-6 ethers. In addition, Monte Carlo (MC) simulations have been used to compute the solubility of the gases CO2, CH4, and N2 in 12-crown-4 and 15-crown-5 ether. The computed properties are compared with available experimental data of crown-ethers and their linear counterparts, i.e., polyethylene glycol dimethyl ethers.