Xiaoqing Zhang

Prof. Xiaoqing Zhang

Tongji University

Research Focus & Metrics

Academic Career Length

33Years (1994-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 April 2023 in Nano Energy
Verified
Journal Article
Closed access
XMXingchen Ma
Xingchen Ma
YQYan Qi
Yan Qi
YNYangyang Niu
Yangyang Niu
QZQi Zhang
Qi Zhang
XXXinhao Xiang
Xinhao Xiang
XZXiaoqing Zhang
Xiaoqing Zhang

14 September 2020 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
SZSergey Zhukov
Sergey Zhukov
XMXingchen Ma
Xingchen Ma
HSHeinz von Seggern
Heinz von Seggern
GSGerhard M. Sessler
Gerhard M. Sessler
ODOmar Ben Dali
Omar Ben Dali
XZXiaoqing Zhang
Xiaoqing Zhang
Polymers with electrically charged internal air cavities (ferroelectrets) reveal a pronounced piezoelectric response and are regarded as soft electroactive multi-functional materials. This work presents preliminary results on the preparation and piezoelectric effect of ferroelectrets based on the polylactic acid (PLA) polymer. A distinctive feature of the manufactured films is that they are biodegradable. After a microstructure modification of carbon dioxide (CO2) foamed PLA sheets by hot-pressing treatment and corona polarization, these cellular films reveal large piezoelectric d 33 and d 31 responses in both quasi-static and dynamic modes. For freshly charged films, the maximum quasi-static piezoelectric coefficients are about 600 pC/N ( d 33 ) and 44 pC/N ( d 31 ) for a relatively thick film of 360 μm and a nominal porosity of about 60%. During the first 20 days after polarization, the piezoelectric activity decreases by half compared to the primary value, but then remains almost unchanged for a long time. Due to an already established inherent biocompatibility of PLA polymers, these eco-friendly ferroelectrets can be potentially used in various biological applications such as biosensors and microenergy harvesters embedded in tissue and artificial muscles.

26 October 2017 in IEEE Sensors Journal
Verified
Journal Article
Closed access
PFPeng Fang
Peng Fang
XMXingchen Ma
Xingchen Ma
XLXiangxin Li
Xiangxin Li
XQXunlin Qiu
Xunlin Qiu
RGReimund Gerhard
Reimund Gerhard
GLGuanglin Li
Guanglin Li
During muscle contractions, radial-force distributions are generated on muscle surfaces due to muscle-volume changes, from which the corresponding body motions can be recorded by means of so-called force myography (FMG). Piezo-or ferroelectrets are flexible piezoelectric materials with attractive materials and sensing properties. In addition to several other applications, they are suitable for detecting force variations by means of wearable devices. In this paper, we prepared piezoelectrets from cellular polypropylene films by optimizing the fabrication procedures, and developed an FMG-recording system based on piezoelectret sensors. Different hand and wrist movements were successfully detected on able-bodied subjects with the FMG system. The FMG patterns were evaluated and identified by means of linear discriminant analysis and artificial neural network algorithms, and average motion-classification accuracies of 96.1% and 94.8%, respectively, were obtained. This paper demonstrates the feasibility of using piezoelectret-film sensors for FMG and may thus lead to alternative methods for detecting body motion and to related applications, e.g., in biomedical engineering or structural-health monitoring.

1 July 2015 in AIP Advances
Verified
Journal Article
Open access
PDF file
XZXiaoqing Zhang
Xiaoqing Zhang
LWLiming Wu
Liming Wu
GSGerhard M. Sessler
Gerhard M. Sessler
Piezoelectret films are prepared by modification of the microstructure of polypropylene foam sheets cross-linked by electronic irradiation (IXPP), followed by proper corona charging. Young’s modulus, relative permittivity, and electromechanical coupling coefficient of the fabricated films, determined by dielectric resonance spectra, are about 0.7 MPa, 1.6, and 0.08, respectively. Dynamic piezoelectric d33 coefficients up to 650 pC/N at 200 Hz are achieved. The figure of merit (FOM, d33 ⋅ g33) for a more typical d33 value of 400 pC/N is about 11.2 GPa−1. Vibration-based energy harvesting with one-layer and two-layer stacks of these films is investigated at various frequencies and load resistances. At an optimum load resistance of 9 MΩ and a resonance frequency of 800 Hz, a maximum output power of 120 μW, referred to the acceleration g due to gravity, is obtained for an energy harvester consisting of a one-layer IXPP film with an area of 3.14 cm2 and a seismic mass of 33.7 g. The output power can be further improved by using two-layer stacks of IXPP films in electric series. IXPP energy harvesters could be used to energize low-power electronic devices, such as wireless sensors and LED lights.

21 September 2021 in Advanced Fiber Materials
Verified
Journal Article
Closed access
PDF file
FXFan Xu
Fan Xu
JYJiang Yang
Jiang Yang
RDRuizhi Dong
Ruizhi Dong
HJHanxiao Jiang
Hanxiao Jiang
CWConghuan Wang
Conghuan Wang
GZGuodong Zhu
Guodong Zhu

3 January 2023 in Advanced Electronic Materials
Verified
Journal Article
Open access
XMXingchen Ma
Xingchen Ma
SZSergey Zhukov
Sergey Zhukov
HSHeinz von Seggern
Heinz von Seggern
GSGerhard M. Sessler
Gerhard M. Sessler
ODOmar Ben Dali
Omar Ben Dali
XZXiaoqing Zhang
Xiaoqing Zhang
Ferroelectrets have promoted a variety of exciting flexible sensors, actuators, and microenergy harvesters. However, most ferroelectrets have been fabricated from non‐degradable petro‐based resins, and thus the recycling of these materials constitutes a big challenge. This article reports biodegradable and bioabsorbable ferroelectret films made from polylactic acid (PLA) resins for highly sensitive transducer applications, which can operate either in piezoelectric 33 or 31/32 mode. By modification of the microstructure and polarization, pronounced longitudinal and transverse piezoelectric activities are realized in a single material. For samples with a thickness of 400 µm and a bulk density of 350 kg m−3, the Young's moduli in thickness and plane direction are ranging from 0.1 to 10 MPa, respectively. After polarization in the thickness direction, quasi‐static piezoelectric d33, g33, d31 (d32), and g31 (g32) coefficients in the PLA films, up to 500 pC N−1, 40 Vm N−1, −44 pC N−1, and −3.6 Vm N−1, are achieved, respectively. The longitudinal piezoelectric coefficients of the PLA films are comparable to non‐degradable polymer ferroelectrets, while the transverse piezoelectric activity is superior, which may be attributed to the reduction of Young's moduli in the plane direction. The preparation procedure of the PLA ferroelectrets is compatible with large‐scale production lines and thus can greatly promote their applications in green electronics.