Xin Fu Tan

Dr. Xin Fu Tan

The University of Queensland
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 February 2023 in Journal of Materials Science & Technology
Verified
Journal Article
Closed access
HYHu Yao
Hu Yao
GZGuang Zeng
Guang Zeng
Xin Fu TanXin Fu Tan
Xin Fu Tan
QGQinfen Gu
Qinfen Gu
KNKazuhiro Nogita
Kazuhiro Nogita
QLQian Li
Qian Li

2 March 2023 in Journal of Materials Science & Technology
Verified
Journal Article
Closed access
Xin Fu TanXin Fu Tan
Xin Fu Tan
MKManjin Kim
Manjin Kim
KYKazuhiro Yasuda
Kazuhiro Yasuda
Kazuhiro NogitaKazuhiro Nogita
Kazuhiro Nogita

1 August 2018 in Small Methods
Verified
Journal Article
Closed access
PDF file
MLMing Li
Ming Li
ZAZhila Amirzadeh
Zhila Amirzadeh
RMRoland De Marco
Roland De Marco
Xin Fu TanXin Fu Tan
Xin Fu Tan
AWAndrew Whittaker
Andrew Whittaker
RKRuth Knibbe
Ruth Knibbe

1 March 2019 in Journal of Power Sources
Verified
Journal Article
Closed access
Xin Fu TanXin Fu Tan
Xin Fu Tan
SMStuart M. Mcdonald
Stuart M. Mcdonald
QGQinfen Gu
Qinfen Gu
YHYuxiang Hu
Yuxiang Hu
Liang WangLiang Wang
Liang Wang
Kazuhiro NogitaKazuhiro Nogita
Kazuhiro Nogita

10 October 2019 in The Journal of Physical Chemistry Letters
Verified
Journal Article
Closed access
MDMatthew Dargusch
Matthew Dargusch
XSXiao-Lei Shi
Xiao-Lei Shi
XTXuan Quy Tran
Xuan Quy Tran
TFTianli Feng
Tianli Feng
FSFlora Somidin
Flora Somidin
Zhi-Gang ChenZhi-Gang Chen
Zhi-Gang Chen

23 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
JZJiye Zhou
Jiye Zhou
Xin Fu TanXin Fu Tan
Xin Fu Tan
SMStuart M. Mcdonald
Stuart M. Mcdonald
Kazuhiro NogitaKazuhiro Nogita
Kazuhiro Nogita
This research evaluates the mechanical properties of a variety of binary In-Sn alloys as potential candidates for low temperature electronic joints. The tensile and hardness tests of as-cast In-5Sn, In-12.5Sn, In-25Sn, In-30Sn, In-35Sn, In-40Sn, In-50Sn, In-60Sn, In-80Sn (wt.%) were assessed at room temperature and compared to those of pure In and Sn. The ultimate tensile strength (UTS) increased from 4.2 MPa to 37.8 MPa with increasing tin content in the alloys under the testing condition of 18 mm/min and the results showed little difference under a lower strain rate (1.8 mm/min). Most compositions showed good ductility in tensile testing with an average of 40% elongation. A melting point range of 119.3 °C to 194.9 °C for tested alloys was measured using differential scanning calorimetry (DSC). The microstructure investigated by scanning electron microscopy (SEM) was discussed with respect to the mechanical properties and it has been found that the presence of the Sn-rich γ-InSn4 phase in the microstructure has a significant impact on mechanical properties. The fundamental data from this study can be used for the development of new low temperature In-Sn alloys.