Yonas Tadesse

Prof. Yonas Tadesse

The University of Texas at Dallas
orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 November 2008 in Journal of Intelligent Material Systems and Structures
Verified
Journal Article
Closed access
PDF file
Yonas TadesseYonas Tadesse
Yonas Tadesse
Shujun ZhangShujun Zhang
Shujun Zhang
Shashank PriyaShashank Priya
Shashank Priya
In this study, we report a multimodal energy harvesting device that combines electromagnetic and piezoelectric energy harvesting mechanism. The device consists of piezoelectric crystals bonded to a cantilever beam. The tip of the cantilever beam has an attached permanent magnet which, oscillates within a stationary coil fixed to the top of the package. The permanent magnet serves two purpose (i) acts as a tip mass for the cantilever beam and lowers the resonance frequency, and (ii) acts as a core which oscillates between the inductive coils resulting in electric current generation through Faraday's effect. Thus, this design combines the energy harvesting from two different mechanisms, piezoelectric and electromagnetic, on the same platform. The prototype system was optimized using the finite element software, ANSYS, to find the resonance frequency and stress distribution. The power generated from the fabricated prototype was found to be 0.25 W using the electromagnetic mechanism and 0.25 mW using the piezoelectric mechanism at 35 g acceleration and 20 Hz frequency.

3 February 2017 in Bioinspiration & Biomimetics
Verified
Journal Article
Closed access
PDF file
LWLianjun Wu
Lianjun Wu
MAMonica Jung de Andrade
Monica Jung de Andrade
LSLokesh Kumar Saharan
Lokesh Kumar Saharan
RRRichard Steven Rome
Richard Steven Rome
RBRay H Baughman
Ray H Baughman
Yonas TadesseYonas Tadesse
Yonas Tadesse
This paper focuses on design, fabrication and characterization of a biomimetic, compact, low-cost and lightweight 3D printed humanoid hand (TCP Hand) that is actuated by twisted and coiled polymeric (TCP) artificial muscles. The TCP muscles were recently introduced and provided unprecedented strain, mechanical work, and lifecycle (Haines et al 2014 Science 343 868-72). The five-fingered humanoid hand is under-actuated and has 16 degrees of freedom (DOF) in total (15 for fingers and 1 at the palm). In the under-actuated hand designs, a single actuator provides coupled motions at the phalanges of each finger. Two different designs are presented along with the essential elements consisting of actuators, springs, tendons and guide systems. Experiments were conducted to investigate the performance of the TCP muscles in response to the power input (power magnitude, type of wave form such as pulsed or square wave, and pulse duration) and the resulting actuation stroke and force generation. A kinematic model of the flexor tendons was developed to simulate the flexion motion and compare with experimental results. For fast finger movements, short high-power pulses were employed. Finally, we demonstrated the grasping of various objects using the humanoid TCP hand showing an array of functions similar to a natural hand.

8 October 2024 in Smart Materials and Structures
Verified
Journal Article
Open access
Mahdi BodaghiMahdi Bodaghi
Mahdi Bodaghi
LWLinlin Wang
Linlin Wang
FZFenghua Zhang
Fenghua Zhang
YLYanju Liu
Yanju Liu
JLJinsong Leng
Jinsong Leng
Ali ZolfagharianAli Zolfagharian
Ali Zolfagharian
Four-dimensional (4D) printing is an advanced manufacturing technology that has rapidly emerged as a transformative tool with the capacity to reshape various research domains and industries. Distinguished by its integration of time as a dimension, 4D printing allows objects to dynamically respond to external stimuli, setting it apart from conventional 3D printing. This roadmap has been devised, by contributions of 44 active researchers in this field from 32 affiliations world-wide, to navigate the swiftly evolving landscape of 4D printing, consolidating recent advancements and making them accessible to experts across diverse fields, ranging from biomedicine to aerospace, textiles to electronics. The roadmap’s goal is to empower both experts and enthusiasts, facilitating the exploitation of 4D printing’s transformative potential to create intelligent, adaptive objects that are not only feasible but readily attainable. By addressing current and future challenges and proposing advancements in science and technology, it sets the stage for revolutionary progress in numerous industries, positioning 4D printing as a transformative tool for the future.

15 July 2019 in Robotics
Verified
Journal Article
Open access
AJAniket Joshi
Aniket Joshi
AKAdwait Kulkarni
Adwait Kulkarni
Yonas TadesseYonas Tadesse
Yonas Tadesse
Several bio-inspired underwater robots have been demonstrated in the last few years that can horizontally swim using different smart actuators. However, very few works have been presented on robots which can swim vertically, have a payload and resemble a jellyfish-like creature. In this work, we present the design, fabrication, and performance characterization of a new tethered robotic jellyfish, which is based on inflatable soft pneumatic composite (SPC) actuators. These soft actuators use compressed air to expand and contract, which help the robot to swim vertically in water. The soft actuators consist of elastomeric air chambers and very thin steel springs, which contribute to gaining faster motion of the biomimetic robot. A prototype of 220 mm in diameter and consisting of eight actuating units was fabricated and tested underwater in a fish tank. It reached a height of 400 mm within 2.5 s while carrying a dead weight of 100 g when tested at 70 psi (483 kPa) pressure. This high performance (160 mm/s on average speed) suggests that faster motion with a payload can be achieved by using SPC actuators. The inflatable structures help to flap the bell segments as well as in buoyancy effect for rapid vertical motion. The major achievement of this work is the ability to demonstrate a novel use of inflatable structures and biomimetic flapping wings for fast motion in water. The experimental and deduced data from this work can be used for the design of future small unmanned underwater vehicles (UUVs). This work adds a new robot to the design space of biomimetic jellyfish-like soft robots. Such kind of vehicle design might also be useful for transporting objects underwater effectively.

5 November 2009 in Journal of Intelligent Material Systems and Structures
Verified
Journal Article
Closed access
Yonas TadesseYonas Tadesse
Yonas Tadesse
NTNicholas Thayer
Nicholas Thayer
Shashank PriyaShashank Priya
Shashank Priya
Application of shape memory alloy (SMA) actuators is limited to low frequencies due to slow cooling time especially in the embedded conditions where heat transfer rate is the controlling factor. In this study, we investigate various active cooling techniques and effect of pre-stress to improve the response time of two commercially available SMAs: Flexinol from Dynalloy Inc. and Biometal fiber from Toki Corporation. Flexinol and Biometal fiber of equal length and diameter were found to exhibit different actuation behavior under pre-stress. Time domain force response of SMA actuators was found to be dependent upon the applied pre-stress, heating rate, and amplitude of applied electrical stimulus. Compared to Biometal fibers, time domain response of Flexinol was found to decrease significantly with increasing pre-stress indicating the difference in transformation behavior. Fluid flow and heat sinking were found to be suitable methods for improving the response time by reducing the cooling cycle from 1.6 s to 0.30—0.45 s. This is a significant improvement in the actuation capability of SMAs.

27 November 2008
Verified
Book Chapter
Closed access
PDF file
HKHyunuk Kim
Hyunuk Kim
Yonas TadesseYonas Tadesse
Yonas Tadesse
Shashank PriyaShashank Priya
Shashank Priya