Yuhao Liu

Prof. Yuhao Liu

Fuzhou University, Fuzhou, Fujian, China

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 December 2024 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
Ying LinYing Lin
Ying Lin
LDLiye Dong
Liye Dong
MDMin Dang
Min Dang
PLPeixuan Li
Peixuan Li
MLMengying Li
Mengying Li
Yuhao LiuYuhao Liu
Yuhao Liu

15 August 2025 in Materials
Verified
Journal Article
Open access
PDF file
FJFu Jianbing
Fu Jianbing
ZLZhifan Lin
Zhifan Lin
JLJunhao Luo
Junhao Luo
YZYufan Zheng
Yufan Zheng
Yuhao LiuYuhao Liu
Yuhao Liu
LWLiming Wang
Liming Wang
Optical fiber composite insulators are essential for photoelectric current measurement, yet insulation failure at embedded optical fiber interfaces remains a major challenge to long-term stability. This study proposes a strategy to replace conventional silicone rubber with cycloaliphatic-like epoxy resin (CEP) as the shed-sheathing material. Three optical fibers with distinct outer coatings, ethylene-tetrafluoroethylene copolymer (ETFE), thermoplastic polyester elastomer (TPEE), and epoxy acrylate resin (EA), were evaluated for their interfacial compatibility with CEP. ETFE, with low surface energy and weak polarity, exhibited poor wettability with CEP, resulting in an interfacial tensile strength of 0 MPa, pronounced dye penetration, and rapid electrical tree propagation. Its average interfacial breakdown voltage was only 8 kV, and the interfacial leakage current reached 35 μA after hygrothermal aging. In contrast, TPEE exhibited high surface energy and strong polarity, enabling strong bonding with CEP, yielding an average interfacial tensile strength of approximately 46 MPa. Such a strong interface effectively suppressed electrical tree growth, increased the average interfacial breakdown voltage to 27 kV, and maintained the interfacial leakage current below 5 μA even after hygrothermal aging. EA exhibited moderate interfacial performance. Mechanism analysis revealed that polar ester and ether groups in TPEE enhanced interfacial electrostatic interactions, restricted the mobility of CEP molecular chain segments, and increased charge traps. These synergistic effects suppressed interfacial charge transport and improved insulation strength. This work offers valuable insight into structure–property relationships at fiber–resin interfaces and provides a useful reference for the design of composite insulation materials.

9 July 2026 in Frontiers in Materials
Verified
Journal Article
Open access
PDF file
YLYing Lin
Ying Lin
YLYating Liu
Yating Liu
Yuhao LiuYuhao Liu
Yuhao Liu
YSYulong Shi
Yulong Shi
TWTao Wen
Tao Wen
Interfacial insulation degradation remains a critical barrier to the reliability of wide-bandgap power electronic packaging subjected to high-frequency pulse voltages and elevated temperatures. This study systematically investigates the electrical treeing behavior at the silicone gel/ceramic substrate interface. It is found that the interfacial electrical treeing exhibits a characteristic three-stage evolutionary process, transitioning from initial sparse dendritic initiation to the rapid expansion of complex reticular cracks, and finally into a stagnation stage where growth rates approach zero. The final tree length follows a linear positive correlation with the pulse voltage amplitude. Besides, the electrical tree length increases significantly with rising frequency in the low-frequency range, while no obvious change in length occurs with further increase in frequency over 5 kHz. On the other hand, the higher the temperature is, the greater the growth rate of electrical trees in the rapid growth stage, and the length of electrical trees increases with the increase in temperature. These findings provide fundamental insights into the interfacial failure mechanisms of elastomeric encapsulants and offer a theoretical framework for designing high-performance insulation systems for next-generation SiC power devices.