Fu Jianbing

Dr. Fu Jianbing


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 August 2025 in Materials
Verified
Journal Article
Open access
PDF file
FJFu Jianbing
Fu Jianbing
ZLZhifan Lin
Zhifan Lin
JLJunhao Luo
Junhao Luo
YZYufan Zheng
Yufan Zheng
Yuhao LiuYuhao Liu
Yuhao Liu
LWLiming Wang
Liming Wang
Optical fiber composite insulators are essential for photoelectric current measurement, yet insulation failure at embedded optical fiber interfaces remains a major challenge to long-term stability. This study proposes a strategy to replace conventional silicone rubber with cycloaliphatic-like epoxy resin (CEP) as the shed-sheathing material. Three optical fibers with distinct outer coatings, ethylene-tetrafluoroethylene copolymer (ETFE), thermoplastic polyester elastomer (TPEE), and epoxy acrylate resin (EA), were evaluated for their interfacial compatibility with CEP. ETFE, with low surface energy and weak polarity, exhibited poor wettability with CEP, resulting in an interfacial tensile strength of 0 MPa, pronounced dye penetration, and rapid electrical tree propagation. Its average interfacial breakdown voltage was only 8 kV, and the interfacial leakage current reached 35 μA after hygrothermal aging. In contrast, TPEE exhibited high surface energy and strong polarity, enabling strong bonding with CEP, yielding an average interfacial tensile strength of approximately 46 MPa. Such a strong interface effectively suppressed electrical tree growth, increased the average interfacial breakdown voltage to 27 kV, and maintained the interfacial leakage current below 5 μA even after hygrothermal aging. EA exhibited moderate interfacial performance. Mechanism analysis revealed that polar ester and ether groups in TPEE enhanced interfacial electrostatic interactions, restricted the mobility of CEP molecular chain segments, and increased charge traps. These synergistic effects suppressed interfacial charge transport and improved insulation strength. This work offers valuable insight into structure–property relationships at fiber–resin interfaces and provides a useful reference for the design of composite insulation materials.

27 February 2026 in Energies
Verified
Journal Article
Open access
PDF file
FJFu Jianbing
Fu Jianbing
YGYanfeng Gao
Yanfeng Gao
LWLiming Wang
Liming Wang
YLYi Lu
Yi Lu
FYFanghui Yin
Fanghui Yin
KWKang Wang
Kang Wang
Silicone rubber optical fiber composite insulators introduce interface defects due to embedded optical fibers, and their structural design remains immature, resulting in inadequate interface sealing performance. In actual operation, the combined effects of high electric fields, high humidity and heat, and mechanical loads lead to frequent failures. This study proposes replacing conventional silicone rubber with cycloaliphatic epoxy resin (CEP), which exhibits superior aging resistance, to enhance long-term operational reliability. However, the correlation mechanism between the structural parameters of CEP optical fiber insulators and their electromechanical properties remains unclear, lacking corresponding design basis. Therefore, based on finite element simulation technology, this study systematically analyzed the influence patterns of core rod diameter, fiber implantation method, spiral groove angle, fiber implantation quantity, and voltage equalization ring structural parameters (outer diameter, circular tube radius, shielding depth) on their mechanical and electrical properties. Research findings indicate that in terms of mechanical properties, the helical groove structure with a 40 mm core rod diameter, a groove angle of 135°, and six embedded optical fibers exhibits the lowest optical fiber strain. In terms of electrical performance, the minimum peak electric field strength at the end of the insulator occurs when the equalizing ring has an outer diameter of 370 mm, the circular tube radius is 25 mm, and the shielding depth is 50 mm, reaching only 4.6 kV/cm, which meets the requirements of DL/T 1000.3-2015. This study establishes optimization principles for key structural parameters of CEP optical fiber composite insulators, offering significant engineering value for enhancing the overall performance of optical fiber composite insulators and improving the operational safety of power systems.