The mechanical properties and fracture characteristics of the high-entropy alloy Al0.5CoCrCuFeNi are studied in different structural states (cast and after two heat treatments) at temperatures of 0.5–300 K with quasistatic deformation by uniaxial compression and distension. Mechanical resonance spectroscopy is used to measure the temperature variations of the Young modulus in the different structural states. It is found that heat treatment of the samples leads to an increase (by roughly 25%) in the Young modulus, the nominal yield point τ0.2, and the deforming stress. The form of the deformation curves is analyzed. The temperature interval for the transition from smooth to discontinuous plastic flow is determined. For the cast state the differences in τ0.2 under tension and compression are determined, an anomalous temperature dependence of τ0.2 (for temperatures in the 0.5–4.2 K range) is discovered, and thermal activation analysis of the experimental data yields empirical estimates for the parameters of the interactions of dislocations with local barriers. After heat treatment the samples break up into two parts under compression, as opposed to the cast state, where the samples acquire a “barrel” shape during compression. It is found that fracture of the heat treated samples at temperatures of 300–4.2 K has a viscous character.
1 September 2014 in International Journal of Plasticity
An integrated approach to the study of the mechanisms of low-temperature dislocation relaxation during low-temperature cyclic deformations of crystalline materials has been developed and tested. The approach is based on the combined use of experimental methods of mechanical spectroscopy in wide frequency-temperature ranges and theoretical methods of statistical and thermoactivation analysis of experimental results. The efficiency of this approach was demonstrated by studying low-temperature relaxation resonances in iron crystals whose dislocation structure was varied by preliminary plastic deformation. In this study, the previous mechanical spectroscopy results for iron in the temperature range of 4 K < T < 150 K at vibrational frequencies of about 1 Hz and 105 Hz were supplemented by a detailed study of the temperature spectra of internal friction and the Young’s modulus of a single-crystal iron plate at intermediate frequencies of about 103 Hz. A two-mode dislocation relaxator model was suggested for interpreting the entire set of experimental results. Its first component is a linear segment of a dislocation line in a first-kind Peierls relief whose relaxation properties are determined by thermal activation of kink pairs. The second component is a chain of geometric kinks capable of thermally activated diffusion movement in a second-kind Peierls relief. Empirical estimates of the energy, force, inertial, and geometric characteristics of both components of such a relaxator have been obtained. This study complements the earlier analysis of the processes of mechanical relaxation in crystals caused by nucleation and movements of kinks on dislocation lines [a review: A. Seeger and C. Wüthrich, Nuovo Cimento B 33, 38 (1976)].
The dynamic elasticity and internal friction of the highly entropic Al0.5CoCrCuFeNi alloy were studied in a wide low temperature range of 4.2–300 K. In the experiments, the bending vibrations of thin plates at a frequency of 530 Hz were studied in two structural states: samples prepared after crystallizing a cast alloy (I); the same samples after prolonged high-temperature annealing (II). The temperature dependences of internal friction Q−1(T) and dynamic Young’s modulus E(T) were obtained and analyzed for these structural states. In state I, both dependences are monotonic functions without any specific features: the internal friction decreases with a decrease in temperature from to , while Young’s modulus increases from EI(T = 300 K); 180 GPa to EI(T = 4.2 K); 190 GPa. Upon the transition to state II, the plot acquires a peak with a height of about 10−4 and a center at Tp; 228 K, without significant changes in internal friction at other temperatures. Young modulus EII(Т) significantly increases (by 20% on average) at all temperatures, and near Tp; 228 K a blurred step with a height of ΔEII ≈ 0.3 GPa ≈ 10−4EII(T =4.2 K) appears on the EII(T) plot. Statistical and thermoactivation analysis of the anomaly of the alloy’s viscoelastic properties near Tp; 228 K by the previously developed algorithm [V. D. Natsik, Yu. A. Semerenko, FNT 42, 185 (2016)] led to the conclusion that it is caused by the resonance interaction of the plate’s elastic vibrations with the dynamic processes in the system of dislocation relaxators, i.e., the thermally activated unpinning of the dislocation segments from the local defects [M. Koiwa and R. R. Hasiguti, Acta Met. 13, 1219 (1965)]. High temperature annealing of the cast alloy is accompanied by significant changes in the morphology and dislocation structure of the samples, which results in a significant increase in their elasticity (Young’s modulus), and the appearance of an internal friction peak at moderately low temperatures. The properties of this peak are similar to those of Hasiguti peaks or β-peaks in simple metals with FCC and BCC lattices.
1 September 2005 in Instruments and Experimental Techniques
A new method of statistically describing the dislocation component of low-temperature internal friction in nanostructured materials. The latter term is applied to ultrafine polycrystals with high density intragranular and grain boundary dislocations, the lines of which are divided into nanometer-scale fragments (dislocation relaxants) with random geometrical and energy parameters. The resonant interaction of elastic vibrations and thermally activated excitations of such relaxators are examined, and the maxima caused by these relaxators along the internal friction temperature dependence are analyzed. It is shown that at low temperatures, the shape of the peaks and the region of their localization along the temperature axis are largely determined by the dispersion of the relaxator activation energy. An algorithm is written in order to analyze the internal friction recorded in the experiment, allowing us to identify the physical model corresponding to the relaxator, and obtain empirical estimates of its parameters.
About Me
My interests include: Low-temperature acoustic relaxation in metals, alloys, amorphous and nanostructured materials.
My interests include: Low-temperature acoustic relaxation in metals, alloys, amorphous and nanostructured materials.