Zheng Liu

Mr. Zheng Liu

Department of Electrical and Computer Engineering, Carnegie Mellon University, Pittsburgh, Pennsylvania, USA
orcid

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 June 2025 in Air
Verified
Journal Article
Open access
PDF file
IKIan Kinsella
Ian Kinsella
APAnna Petrbokova
Anna Petrbokova
RYRongjie Yang
Rongjie Yang
Zheng LiuZheng Liu
Zheng Liu
GNGokul Nathan
Gokul Nathan
SMSepehr Makhsous
Sepehr Makhsous
Soldering is a common engineering practice that releases airborne particulate matter (PM), contributing to significant long-term respiratory risk. The health impact of this exposure is significant, with up to 22% of soldering workers worldwide being diagnosed with conditions such as occupational asthma, restrictive lung disease, and bronchial obstruction. Studies have reported that soldering can produce PM2.5 concentrations up to 10 times higher than the U.S. Environmental Protection Agency’s (EPA) 24 h exposure limit of 35.0 μg/m3—posing significant respiratory and cognitive health risks under chronic exposure. These hazards remain underappreciated by novice engineers in academic and entry-level industrial environments, where safety practices are often informal or inconsistently applied. Air purification systems offer a mitigation approach; however, performance varies significantly with model and placement, and independent validation is limited. This study uses an indoor air quality monitoring system consisting of six AeroSpec sensors to measure PM2.5–10 concentrations during soldering sessions conducted with and without commercial air purifiers. Tests were conducted with and without a selection of commercial air purifiers, and measurements were recorded under consistent spatial and temporal conditions. Datasets were analyzed to evaluate purifier effectiveness and the influence of placement on pollutant distribution. The findings provide independent validation of air purifier capabilities and offer evidence-based suggestions for minimizing particulate exposure and improving safety in laboratory soldering environments.

29 July 2026 in Air
Verified
Journal Article
Open access
PDF file
Zheng LiuZheng Liu
Zheng Liu
GNGokul Nathan
Gokul Nathan
XXXueyicheng Xu
Xueyicheng Xu
MYMingcheng Yang
Mingcheng Yang
KPKavimitiran Pasupathi
Kavimitiran Pasupathi
SMSepehr Makhsous
Sepehr Makhsous
Public fireworks shows are widely used for national holiday celebrations, religious ceremonies, and sports events. However, fireworks produce short-lived atmospheric particulate matter (PM) peaks, posing a risk to spectators’ health. Every year, public fireworks shows expose over 140 million Americans to episodic transient PM2.5 peaks that exceed air quality standards by up to 10 times in the United States alone. Yet the magnitude and timing of this representativeness gap have not been measured within an event. This paper investigates the Independence Day fireworks display over Lake Union, Seattle, WA, USA, using a low-cost PM network deployed up to 2 km from the launch site. We evaluated the network observations against routine monitoring data from regulatory stations within 10 km of the launch site and generated a backward–forward Lagrangian stochastic dispersion model, calibrated with the network. Spectator zone PM2.5 concentrations varied by over threefold across sensors within 1.5 km. Duration above the World Health Organization (WHO) 24 h PM2.5 guideline concentration level at network sensors varied from 1 min to nearly 30 min, and regulatory hourly averaging retained 57% of the near-field peak signal on average and only 22% in the worst case. Peak detection at some regulatory stations was delayed by one to two hours compared with the network. The dispersion model, using only network data and public regional wind data, captured the launch site location to within ~100 m and provided minute-scale estimates of PM2.5 and PM1 concentrations across the spectator zone. The findings demonstrate and quantify, for a single event, the representativeness gap expected when transient near-field fireworks plumes are evaluated using spatially sparse and hourly averaged regulatory observations.

13 October 2026 in Sensors
Verified
Journal Article
Open access
PDF file
OPOlga Podkorytova
Olga Podkorytova
MYMingcheng Yang
Mingcheng Yang
YCYancheng Chen
Yancheng Chen
MMMaxwell Mamishev
Maxwell Mamishev
EJEric Jiang
Eric Jiang
SMSepehr Makhsous
Sepehr Makhsous
Automated guided vehicles and mobile robots are present on many Intelligent Manufacturing factory floors. Approximately 7.0 million U.S. workers also work on those same floors. During 2011 through 2017, forklifts caused 614 worker fatalities. Currently, no commercially available collision-avoidance sensor can manage the complexity associated with working within a plant. Therefore, fusing multiple modalities allows a system designer to gate the more expensive ones behind some minimal signal that indicates all systems should be active. Such minimal signals are expected to include body heat that even stationary personnel would have difficulty suppressing. In addition, the signal-capturing sensors ought to operate at milliwatt levels of power while keeping workers’ privacy. One type of device that has been found suitable for these requirements is a coarse thermopile array. Such a device can be fused with a rangefinder that determines distance to form a gated system. Yet the measurement capability frontier of the thermopile arrays in practical scenarios has not been explored. In addition, there is currently no figure of merit to quantify the trade-ff between induced errors and system-level power saving. In order to address these gaps, we built the fusion system, Firefly, together with a training-free detector and tested them against a human and a mannequin 1.2 to 7 m away in four thermally distinct environments, one of which is the floor of an operating factory. We found that the thermal array’s detection range varies with the environment but is predictable in a thermally uniform environment. Based on these experiments, we also proposed the Gated-Fusion Efficiency (GFE), a figure of merit that converts a trigger’s error rates into system-level power savings. Together, the capability boundary and the GFE help guide sensor-fusion system design in industrial manufacturing toward safer working environments.

1 October 2026 in IEEE Sensors Letters
Verified
Journal Article
Closed access
KAKarlen Aleksanyan
Karlen Aleksanyan
XXXueyicheng Xu
Xueyicheng Xu
Zheng LiuZheng Liu
Zheng Liu
HLHaitao Lin
Haitao Lin
GNGokul Nathan
Gokul Nathan
AMAlexander V. Mamishev
Alexander V. Mamishev