This study elucidated the synergistic improvement of the interfacial performance and impact resistance of carbon fiber-reinforced epoxy (CF/EP) composites by employing continuous electrochemical oxidation. CFs were electrochemically treated at different current densities, and the surface physicochemical properties, including the surface morphologies, chemical compositions, and wettabilities, were analyzed. After electrochemical oxidation, the IFSS of the CF/EP increased by 48.8%, significantly improving the impact resistance of the composites. The experimental results showed that, when the current density reached 0.15 mA/cm2, the damage area after impact reduced by 61%. Concurrently, fiber fracture and resin failure became the primary energy-dissipation modes, maximizing the fiber reinforcement effect and enhancing the impact resistance. However, fiber fracture deteriorated the static mechanical properties of the composites. Subsequently, at a 0.10 mA/cm2 current density, the CF/EP composites exhibited an increased compressive strength after an impact of 331 MPa.
The toughening modification of epoxy resin has received widespread attention. The addition of the second-phase resin has a good toughening effect on epoxy resin. In order to investigate the effect of the second-phase resin on the interphase of composites, in this work the interfacial properties of carbon fiber (CF)/epoxy resin with the second-phase resin structure were investigated. Methodologies including surface structure observation, chemical characteristics, surface energy of the CF, and micro-phase structure characterization of resin were tested, followed by the micro-interfacial performance of CF/epoxy composites before and after hygrothermal treatment. The results revealed that the sizing process has the positive effect of increasing the interfacial bonding properties of CF/epoxy. From the interfacial shear strength (IFSS) test, the introduction of the second phase in the resin reduced the interfacial bonding performance between the CF and epoxy. After the hygrothermal treatment, water molecules diffused along the interfacial paths between the two resins, which in turn created defects and consequently brought about a reduction in the IFSS.
This work investigated the effects of moisture absorption treatment on composite−to−metal double−lap shear joints (DLSJs) bonded with epoxy adhesive film through experiments and simulations. The composite−to−metal DLSJ can be divided into five parts (the interface between the composite and adhesive, the interface between the adhesive and metal, the composite adherend, the metal adherend, and the adhesive layer). First, the wet−dependent properties of the adhesive and interfaces were obtained through adhesive tensile tests and GC tests, which showed that the properties of the adhesive and interfaces were significantly affected by the moist environment. Then, tensile tests of the composite−to−metal double−lap shear joints were carried out in dry and wet environments. Finally, based on the experimental investigations, a finite element (FE) model that considered cohesive damage was established for simulating damage evolution and predicting the failure loads and failure modes of the DLSJs. The results of both the experimental and numerical tests show that the DLSJ failure load decreases significantly after immersion in 95 °C water, and the major failure mode transfers from adhesive failure to interface failure. The research results provide a theoretical basis or basic data for the structural design of adhesively bonded composite−to−metal.
In this study, a one-pot aryl diazonium reaction was used as a simple and mild method to graft graphene onto the smooth and inert surface of T1100-grade carbon fiber (CF) through covalent bonding without any damage on CF, to refine the interface performance of CF/bismaleimide (BMI) composites. XPS, SEM, AFM, and dynamic contact angle testing (DCAT) were used to characterize chemical activity, morphologies, and wettability on untreated and grafted CF surfaces. Meanwhile, the impact of the graft method on the tensile strength of CF was also examined using the monofilament tensile test. IFSS between CF grafted with graphene and BMI resin achieved 104.2 MPa after modification, increasing from 85.5 MPa by 21.8%, while the tensile strength did not decrease compared to the pristine CF. The mechanism of this interface enhancement might be better chemical bonding and mechanical interlock between CF grafted with graphene and BMI resin, which is generated from the high surface chemical activity and rough structure of graphene. This study may propose a simple and mild method to functionalize the CF surface and enhance the interface performance of composites without compromising the tensile properties of T1100-grade CF.