Tian Qiu

Dr. Tian Qiu


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 December 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
CGChenyu Gan
Chenyu Gan
QMQinglin Ma
Qinglin Ma
SBShengyu Bao
Shengyu Bao
XWXinming Wang
Xinming Wang
TQTian Qiu
Tian Qiu
丁水汀 Dingshuiting丁水汀 Dingshuiting
丁水汀 Dingshuiting
Sustainable aviation fuels (SAFs) are considered an important solution for reducing carbon emissions. Safety is the most important prerequisite for a new fuel to be used in an aero-engine. As a special component in aero-engines, fuel is required to comply with both airworthiness and technical standards. These two types of standard work together to guide SAF development. In this paper, the SAF safety issues related to aero-engines are first analyzed. Subsequently, SAF-related standard systems are analyzed in detail, and the different safety responsibilities of airworthiness authorities and industry associations are explained. Moreover, the relationships between airworthiness and technical standards are determined from the perspective of actual SAF certification. Furthermore, the revision of the standards is reviewed to summarize the historical evolution and outline the revision intention. Finally, the future SAF certification standards are discussed and prospected, including the blending ratio, property specifications, and testing equipment. According to the discussion, increased safety and fewer constraints are the principal objectives for the development of SAF standards. Analysis, review, and discussion of the SAF standards systems from an aero-engine safety perspective will contribute to the establishment of the next generation of standards to release the fuel potential and improve safety.

31 January 2023 in Aerospace
Verified
Journal Article
Open access
PDF file
YSYu Shi
Yu Shi
丁水汀 Dingshuiting丁水汀 Dingshuiting
丁水汀 Dingshuiting
Peng LiuPeng Liu
Peng Liu
TQTian Qiu
Tian Qiu
CLChuankai Liu
Chuankai Liu
DYDahai Ye
Dahai Ye
In the typical structure of a turboshaft aero-engine, the mass flow of the cooling air in the rotor-stator cavity is controlled by the inlet seal labyrinth. This study focused on the swirl flow and heat transfer characteristics in a rotor-stator cavity with considerations of the inlet seal thermal deformation effect. A numerical framework was established by integrating conjugate heat transfer (CHT) analysis and structural finite element method (FEM) analysis to clarify the two-way aero-thermo-elasto coupling interaction among elastic deformation, leakage flow, and heat transfer. Simulation results showed that the actual hot-running clearance was non-uniform along the axial direction due to the temperature gradient and inconsistent structural stiffness. Compared with the cold-built clearance (CC), the minimum tip clearance of the actual non-uniform hot-running clearance (ANHC) was reduced by 37–40%, which caused an increase of swirl ratio at the labyrinth outlet by 5.3–6.9%, a reduction of the Nusselt number by up to 69%. The nominal uniform hot-running clearance (NUHC) was defined as the average labyrinth tip clearance. The Nusselt number of the rotating disk under the ANHC was up to 81% smaller than that under the NUHC. Finally, a clearance compensation method was proposed to increase the coolant flow and decrease the metal temperature.

5 October 2022 in Aerospace
Verified
Journal Article
Open access
PDF file
SZShenghui Zhang
Shenghui Zhang
丁水汀 Dingshuiting丁水汀 Dingshuiting
丁水汀 Dingshuiting
Peng LiuPeng Liu
Peng Liu
TQTian Qiu
Tian Qiu
In advanced civil aero-engine, the gas exiting combustor typically features hot streak (HS) and swirl that affect the aerothermal performances of the high pressure (HP) nozzle guide vane (NGV). The purpose of this paper is to study the influences of HS on HP NGV aerothermal behaviors under swirl with various intensities. The numerical investigations were conducted on the first NGV of GE-E3 HP turbine. Four swirl intensities (|SN| = 0, 0.25, 0.50, 0.75) and two swirl orientations (positive and negative) were considered. The result indicates that the relative strengths between the swirl and its induced radial pressure gradient dominate the flow patterns on vane surfaces. Thus, the diverse streamlines distributions appear on the surfaces and the dominated factor on each surface does not vary with swirl intensity. The swirl redistributes the cold and hot fluid and thus generates the relatively hot oblique strip and cold region at the upstream of vane. The heat load on the vane that is not directly impinged by HS is dictated by the radial migration of the fluids originating from the regions aforementioned at |SN| = 0.25 and 0.50. However, at |SN| = 0.75, the transverse movement of HS due to the intense swirl causes additional thermal load. The heat load on the vane that faces HS is mainly determined by the radial migration of HS. The swirl alters the heat transfer distribution on vane surfaces remarkably. With positive swirl, the heat transfer coefficients at the lower span of suction side and pressure side are enhanced and weakened respectively. As expected, the opposite trends are observed in the negative swirl case. Swirl also affects boundary layer transition, and then affecting heat transfer. Positive and negative swirls both advance the transition on the suction side of vane directly impinged by the swirl, and with the increase of swirl intensity, transition onset shifts toward upstream.

1 May 2024 in Sustainability
Verified
Journal Article
Open access
PDF file
丁水汀 Dingshuiting丁水汀 Dingshuiting
丁水汀 Dingshuiting
QMQinglin Ma
Qinglin Ma
TQTian Qiu
Tian Qiu
CGChenyu Gan
Chenyu Gan
XWXinming Wang
Xinming Wang
Safety is essential for sustainable aviation fuels (SAFs). However, evaluating SAFs’ impacts on aero-engine safety is challenging because it involves multiple space scales and the strongly coupled relationships of aero-engine components. Aiming at addressing this problem, a model-based approach is proposed to establish the relationship between the fuel-level physical properties and engine-level safety parameters. Firstly, a unified modeling criterion is proposed to consider the interrelations of aero-engine components. Under this criterion, aero-engine secondary air system (SAS) components are included in SAF safety assessment, since they have non-neglectable influences on aero-engine safety. Secondly, this paper proposes a surrogate-based iteration strategy to embed the combustor’s high-dimensional computational fluid dynamics (CFD) model into the aero-engine flow network model. Then, the proposed model-based safety assessment approach is applied to a Fischer–Tropsch hydro-processed synthesized paraffinic kerosine (F-T SPK) safety assessment case. The effects of fuel flow and blending ratio are considered. The results indicate the necessity to evaluate SAFs’ safety at the aero-engine level and consider the influences of SAS components. The proposed model-based approach may provide a preliminary screening before SAFs’ certification tests. This convenience may be beneficial for reducing the cost and accelerating SAFs’ application.

1 June 2021 in International Journal of Pressure Vessels and Piping
Verified
Journal Article
Closed access
LYLicai Yang
Licai Yang
TQTian Qiu
Tian Qiu
YQYang Qiu
Yang Qiu
SZShanglin Zhang
Shanglin Zhang
YLYuguang Li
Yuguang Li

16 February 2022 in Aerospace
Verified
Journal Article
Open access
PDF file
GZGang Zhao
Gang Zhao
TQTian Qiu
Tian Qiu
Peng LiuPeng Liu
Peng Liu
Rotor-stator cavities are often found in turbomachinery; they supply cold air that is bled from the compressor to the turbine blades. The pressure of the outlet of a rotor-stator cavity is axisymmetric under normal circumstances. However, its pressure would be non-axisymmetric in the event of blade fracture. The impact of blade fracture on a rotor-stator cavity with centrifugal superposed flow is studied in this paper. The Euler number E, the rotational Reynolds number Reφ, and the low-pressure zone range θ are investigated and, for the first time, with the non-axisymmetrical boundary conditions employing numerical simulation. The results of the numerical calculations show that after turbine blade fracture, the velocity is more affected in the downstream region at a high radius, especially when the Reφ is large. As for the distribution of the mass flow rate, there may be a critical θc at which the other blades are least affected. The θc would increase as the Reφ or the E increase, and the θc≅0.2 when Cw=10,137, Reφ=5.12×105, and 0.2≤E≤0.4. In addition, the thrust coefficient increases as the E or the θ increases, and the increase in the thrust coefficient does not exceed 4% when the E=0.2 and the θ=0.1 in this paper. However, the moment coefficient on the rotating shaft is almost independent of the E and the θ. An increase in the Reφ will reduce the effect of turbine blade fracture on the thrust and moment coefficients, when the Reφ is small.