Energy storage and conversion is a very important link between the steps of energy production and energy consumption. Traditional fossil fuels are a natural and unsustainable energy storage medium with limited reserves and notorious pollution problems, therefore demanding a better choice to store and utilize the green and renewable energies in the future. Energy and environmental problems require a clean and efficient way of using the fuels. Fuel cell functions to efficiently convert oxidant and chemical energy accumulated in the fuel directly into DC electric, with the by-products of heat and water. Fuel cells, which are known as effective electrochemical converters, and electricity generation technology has gained attention due to the need for clean energy, the limitation of fossil fuel resources and the capability of a fuel cell to generate electricity without involving any moving mechanical part. The fuel cell technologies that received high interest for commercialization are polymer electrolyte membrane fuel cells (PEMFCs), solid oxide fuel cells (SOFCs), and direct methanol fuel cells (DMFCs). The optimum efficiency for the fuel cell is not bound by the principle of Carnot cycle compared to other traditional power machines that are generally based on thermal cycles such as gas turbines, steam turbines and internal combustion engines. However, the fuel cell applications have been restrained by the high cost needed to commercialize them. Researchers currently focus on the discovery of different materials and manufacturing methods to enhance fuel cell performance and simplify components of fuel cells. Fuel cell systems’ designs are utilized to reduce the costs of the membrane and improve cell efficiency, durability and reliability, allowing them to compete with the traditional combustion engine. In this review, we primarily analyze recent developments in fuel cells technologies and up-to-date modeling for PEMFCs, SOFCs and DMFCs.
Efficient and effective lubricants have great application prospects in the manufacturing industries. Minimum quantity lubrication (MQL) machining with low flow rate of nanolubricants is investigated for cooling and lubrication during the process. This paper investigates the characterization of graphene-mixed aluminium oxide (G-Al2O3) hybrid nanomixture spent lubricants for MQL machining purposes. The main advantage of this method is to reduce the disposal lubricants to develop high-performance cooling-lubrication by using nanolubricants of G-Al2O3 nanoparticles in different volume composition ratios at a constant 1.0% volume concentration in a base liquid mixture of 40% spent lubricants. Before conducting the measurements of the nanolubricants’ thermal conductivity and dynamic viscosity, the nanolubricants were homogenous and stable. The tribological performance of all ratios was evaluated by using a four-ball wear tribotester machine. The thermal conductivity peak value for the G-Al2O3 hybrid nanolubricant was obtained and the highest enhancement, up to 29% higher than the base liquid solution, was obtained. The dynamic viscosity variation for all ratios was lower than the 40:60 ratio. The properties enhancement ratio suggests that G-Al2O3 hybrid nanolubricants with 1.0% volume concentration aid in the heat transfer, especially for ratios of 60:40 and 20:80. The lowest coefficient of friction (COF) for a ratio of 60:40 was obtained to be 0.064, with 45% enhancement as compared to the base liquid solution. In conclusion, optimum ratios for G-Al2O3 hybrid nanolubricants were determined to be 20:80 and 60:40. Regarding the properties enhancement ratio, the combination of enhanced thermophysical and tribological properties had more advantages for cooling lubrication application.
19 March 2018 in IOP Conference Series: Materials Science and Engineering
Cutting process of difficult-to-cut material such as stainless steel, generates immensely excessive heat, which is one of the major causes related to shortening tool life and lower quality of surface finish. It is proven that application of cutting fluid during the cutting process of difficult-to-cut material is able to improve the cutting performance, but excessive application of cutting fluid leads to another problem such as increasing processing cost and environmental hazardous pollution of workplace. In the study, Extreme Cold Mist system is designed and tested along with various Minimum Quantity Lubrication (MQL) systems on turning process of stainless steel AISI 316. In the study, it is obtained that, Extreme Cold Mist system is able to reduce cutting force up to 60N and improve the surface roughness of the machined surface significantly.
28 April 2018 in Lecture Notes in Mechanical Engineering