Alexander Nikitin

Mr. Alexander Nikitin


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2024 in Metals
Verified
Journal Article
Open access
PDF file
Georgi KotlarskiGeorgi Kotlarski
Georgi Kotlarski
Maria OrmanovaMaria Ormanova
Maria Ormanova
Alexander NikitinAlexander Nikitin
Alexander Nikitin
IMIuliia Morozova
Iuliia Morozova
RORalf Ossenbrink
Ralf Ossenbrink
S. ValkovS. Valkov
S. Valkov
In the current paper, the correlation between the physical size of additively built wire arc specimens and their structure and properties is studied. For the purpose of this work, two oval shaped specimens of different lengths were manufactured under the same technological conditions. The specimens have a length of 200 mm and 400 mm and will be referred to as L200 and L400. The microstructure of the samples was studied using X-ray diffraction analysis (XRD), optical microscopy, and scanning electron microscopy (SEM). The microhardness, yield strength (YS), and ultimate tensile strength (UTS) were determined and their correlation with the technological conditions of specimen build-up was clarified. The results of the carried out experiments indicated that the crystallographic structure of both specimens is similar. The scanning electron microscopy images show a higher concentration of irregularly shaped micro-pores formed near the edge of the αAl grains in the structure of the L400 specimen compared to the L200 one. An increase in the size of the αAl solid solution grains in the case of the L200 specimen towards its top section was noticed using optical microscopy. A slightly lower magnitude change was noticed concerning the L400 specimen. The increase in the size of the aluminum crystals was determined to be the increasing interpass temperature. Due to the much smaller thermal dissipation capacity of the smaller specimen, the interpass temperature of the same increased faster compared to the larger specimen. All of the above-mentioned factors led to a decrease in the microhardness of the specimens at higher stages of build-up. Since the specimens were deposited using similar layer deposition conditions, the resultant YS and UTS data are also highly comparable.

2 November 2022 in Metals
Verified
Journal Article
Open access
PDF file
Georgi KotlarskiGeorgi Kotlarski
Georgi Kotlarski
Maria OrmanovaMaria Ormanova
Maria Ormanova
RORalf Ossenbrink
Ralf Ossenbrink
Alexander NikitinAlexander Nikitin
Alexander Nikitin
NDNikolay Doynov
Nikolay Doynov
VMVesselin Michailov
Vesselin Michailov
For the purpose of this research, single track details were manufactured in the shape of thin walls with a length of 100 mm and a height of 80 mm. Two welding speeds were chosen for this experiment–13.3 mm/s and 20.0 mm/s corresponding to the following heat inputs: 120 J/mm and 80 J/mm. The gas metal arc welding (GMAW) method was used for the build-up of the specimens in the cold arc pulse mode. The structure of the specimens was studied using X-ray diffraction (XRD) analysis carried out with CuKα radiation with a wavelength of 1.5406 Ǻ, optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). Furthermore, the Vickers hardness of the samples was determined using a ZwickRoell DuraScan 10/20 G5 unit at a force of 1 N. A preferred crystallographic orientation towards the (200) plane was observed in all cases, however a vastly textured structure was observed with inclusions of peaks in the (111), (220), and (311) crystallographic planes. The full width at half maximum (FWHM) of samples taken from different stages of build-up was calculated indicating an increase of the dislocation density at the more advanced stages of specimen growth. Despite that an increase of the hardness was observed towards the top of both specimens. This is attributed to the change in the structure of the αAl + Si formations from an irregular one at the bottom of the specimens, towards a fibrous one at the top. The results are discussed in regard to the optimization of the build-up process during wire arc additive manufacturing (WAAM).

18 January 2024 in Machines
Verified
Journal Article
Open access
PDF file
Georgi KotlarskiGeorgi Kotlarski
Georgi Kotlarski
MOMaria Ormanova
Maria Ormanova
Alexander NikitinAlexander Nikitin
Alexander Nikitin
IMIuliia Morozova
Iuliia Morozova
RORalf Ossenbrink
Ralf Ossenbrink
S. ValkovS. Valkov
S. Valkov
The mass production of metallic components requires high agility in the working process conditioned by the necessity of building details of different shapes and sizes. Changing the size of the components theoretically influences the thermal dissipation capability of the same, which could lead to a change in their structure and mechanical properties. This is particularly important when aluminum alloys are concerned. For this reason, two Al5356 single-track specimens were built using the same technological conditions of layer deposition by varying only their geometrical size. In all cases, the specimens were wire and arc additively manufactured (WAAM) using a process based on gas metal arc welding (GMAW) in the cold arc pulse mode (CAP). The structure of both specimens was studied and defects along their surfaces were detected in the form of micro-pores and micro-cracks. A high concentration of undissolved Mg particles was also detected, along with some standalone Si particles. Uniformity in the build-up process was achieved, which led to the formation of nearly identical structures in the specimens. Subsequently, the resultant mechanical properties were also highly comparable. This indicates that the geometry-related variation in thermal conditions has an insignificant influence on the component’s structure and properties.

19 November 2024 in Welding in the World
Verified
Journal Article
Open access
PDF file
Alexander NikitinAlexander Nikitin
Alexander Nikitin
DTD. Turabov
D. Turabov
EEE. Ermilova
E. Ermilova
AEA. Evdokimov
A. Evdokimov
ROR. Ossenbrink
R. Ossenbrink
HSH. Seidlitz
H. Seidlitz
In this study, the correlation between dynamic resistance during the first 10 ms of welding time and the electrode surface condition in resistance spot welding of 5182 aluminum alloy has been investigated. The electrode surface rapidly degrades due to contamination and morphological changes, adversely affecting the weld spot surface. The accumulation of Cu-Al intermetallic phases on the electrode surface alters its roughness, leading to variations in dynamic resistance. By analyzing this correlation, optimal electrode milling intervals were identified to extend electrode life. This work focused on detecting crater formation on the electrode surface through dynamic resistance monitoring. The results indicate that resistance measurements provide a reliable approach for evaluating electrode wear, optimizing maintenance schedules, and reducing material removal during milling.

1 January 2017 in International Journal of Corrosion
Verified
Journal Article
Open access
PDF file
Alexander NikitinAlexander Nikitin
Alexander Nikitin
LSL. Schleuss
L. Schleuss
RORalf Ossenbrink
Ralf Ossenbrink
VMVesselin Michailov
Vesselin Michailov
Arc brazing has, in comparison to arc welding, the advantage of less heat input while joining galvanized sheet metals. The evaporation of zinc is reduced in the areas adjacent to the joint and improved corrosion protection is achieved. In the automotive industry, lightweight design is a key technology against the background of the weight and environment protection. Structured sheet metals have higher stiffness compared to typical automobile sheet metals and therefore they can play an important role in lightweight structures. In the present paper, three arc brazing variants of galvanized structured sheet metals were validated in terms of the corrosion behavior. The standard gas metal arc brazing, the pulsed arc brazing, and the cold metal transfer (CMT®) in combination with a pulsed cycle were investigated. In experimental climate change tests, the influence of the brazing processes on the corrosion behavior of galvanized structured sheet metals was investigated. After that, the corrosion behavior of brazed structured and flat sheet metals was compared. Because of the selected lap joint, the valuation of damage between sheet metals was conducted. The pulsed CMT brazing has been derived from the results as the best brazing method for the joining process of galvanized structured sheet metals.

28 June 2024 in Materials
Verified
Journal Article
Open access
PDF file
MKMarcel Köhler
Marcel Köhler
Alexander NikitinAlexander Nikitin
Alexander Nikitin
PSPeter Sonnenfeld
Peter Sonnenfeld
RORalf Ossenbrink
Ralf Ossenbrink
SJSven Jüttner
Sven Jüttner
Composite materials made from aluminum foam are increasingly used in aerospace and automotive industries due to their low density, high energy absorption capacity, and corrosion resistance. Additive manufacturing processes offer several advantages over conventional manufacturing methods, such as the ability to produce significantly more geometrically complex components without the need for expensive tooling. Direct Energy Deposition processes like Wire Arc Additive Manufacturing (WAAM) enable the additive production of near-net-shape components at high build rates. This paper presents a technology for producing aluminum foam structures using WAAM. This paper’s focus is on the development of welding wires that are mixed with a foaming agent (TiH2) and produce a foamed weld metal as well as their processing using MIG welding technology.