This study investigates the impact of an increased bio-content on the mechanical properties of bio-based epoxy resins. Cardanol-based epoxy and novolac resins (65% and 84% bio-content, respectively) were combined with two commercial cardanol-based epoxy systems to achieve higher total bio-contents. Quasi-static tensile tests showed that resin blends with up to 40% bio-content maintain tensile properties comparable to traditional formulations, with a glass transition temperature (Tg) suitable for automotive requirements. The results highlight that an increased bio-content enhances flexibility and viscoelastic behavior. Additionally, the tests showed that epoxy resins with a high bio-content represent a sustainable alternative with reduced environmental impact. This work benchmarks novel cardanol-based epoxy formulations with existing bio-based systems, supporting their industrial application.
The cure kinetics of various epoxy resin mixtures, comprising a bisphenol epoxy, two epoxy modifiers, and two hardening agents derived from cardanol technology, were investigated through differential scanning calorimetry (DSC). The development of these mixtures aimed to achieve epoxy materials with a substantial bio-content up to 50% for potential automotive applications, aligning with the 2019 European Regulation on climate neutrality and CO2 emission. The Friedman isoconversional method was employed to determine key kinetic parameters, such as activation energy and pre-exponential factor, providing insights into the cross-linking process and the Kamal–Sourour model was used to describe and predict the kinetics of the chemical reactions. This empirical approach was implemented to forecast the curing process for the specific oven curing cycle utilised. Additionally, tensile tests revealed promising results showcasing materials’ viability against conventional counterparts. Overall, this investigation offers a comprehensive understanding of the cure kinetics, mechanical behaviour, and thermal properties of the novel epoxy–novolac blends, contributing to the development of high-performance materials for sustainable automotive applications.
A new phenomenological constitutive model is proposed for the prediction of the tensile and compressive behavior of semi‐crystalline and amorphous polymers. The new model modifies the phenomenological model previously proposed by Zhou and Mallick (ZM model) to correctly predict the complex behavior of thermoplastic materials including the linear viscoelastic deformation, the non‐linear viscoelastic deformation, the yielding, the post‐yield strain softening and the post‐yield strain hardening. A validation activity based on literature data has been carried out for polyether‐ether‐ketone (PEEK) and polycarbonate (PC) materials. The new model proved effective in fitting with high accuracy all the phases of the flow stress behavior for the considered materials, across a wide range of strain rates and temperature conditions. Finally, the comparison with Zhu et al., Duan et al., Nasraoui et al., Mulliken‐Boyce and Zhou‐Mallick models showed the better fitting performance of the proposed phenomenological model.Highlights: Formulation of a new phenomenological model. Validation on mechanical test of semi‐crystalline and amorphous thermoplastics. Comparison with different phenomenological models present in the literature. Superior prediction results achieved compared to previously developed models.
The present paper aims to broaden the field of application of the phenomenological model proposed by the authors in a previous study (ICP model) and to assess the shear properties of a recycled 30 wt.% talc-filled polypropylene (TFPP) and a recycled 30 wt.% short glass fiber-reinforced polypropylene (SGFPP), used in the automotive industry. The materials were produced by injection molding employing post-industrial mechanical shredding of recycled materials. In particular, Iosipescu shear tests adopting the American Standard for Testing Materials (ASTM D5379) at three different operating temperatures (−40, 23 and 85 °C) were performed. The strain was acquired using a Digital Image Correlation (DIC) system to determine the map of the strain in the area of interest before failure. Lower operating temperatures led to higher shear chord moduli and higher strengths. Recycled SGFPP material showed higher mechanical properties and smaller strains at failure with respect to recycled TFPP. Finally, the ICP model also proved to be suitable and accurate for the prediction of the shear behavior of 30 wt.% SGFPP and 30 wt.% TFPP across different operating temperatures.