The fullerene C60 is commonly applied as the electron transport layer in high‐efficiency metal halide perovskite solar cells and has been found to limit their open circuit voltage. Through ultra‐sensitive near‐UV photoelectron spectroscopy in constant final state mode (CFSYS), with an unusually high probing depth of 5–10 nm, the perovskite/C60 interface energetics and defect formation is investigated. It is demonstrated how to consistently determine the energy level alignment by CFSYS and avoid misinterpretations by accounting for the measurement‐induced surface photovoltage in photoactive layer stacks. The energetic offset between the perovskite valence band maximum and the C60 HOMO‐edge is directly determined to be 0.55 eV. Furthermore, the voltage enhancement upon the incorporation of a LiF interlayer at the interface can be attributed to originate from a mild dipole effect and probably the presence of fixed charges, both reducing the hole concentration in the vicinity of the perovskite/C60 interface. This yields a field effect passivation, which overcompensates the observed enhanced defect density in the first monolayers of C60.
Various crystallite size estimation methods were used to analyze X-ray diffractograms of spherical cerium dioxide and titanium dioxide anatase nanoparticles aiming to evaluate their reliability and limitations. The microstructural parameters were estimated from several integral breadth methods such as Scherrer, Monshi, Williamson–Hall, and their variants: (i) uniform deformation model, (ii) uniform strain deformation model, and (iii) uniform deformation energy density model. We also employed the size–strain plot and Halder–Wagner method. For this purpose, an instrumental resolution function of an Al2O3 standard was used to subtract the instrumental broadening to estimate the crystallite sizes and strain, and the linear regression analysis was used to compare all the models based on the coefficient of determination. The Rietveld whole powder pattern decomposition method was introduced for comparison purposes, being the best candidate to fit the X-ray diffraction data of metal-oxide nanoparticles. Refined microstructural parameters were obtained using the anisotropic spherical harmonic size approach and correlated with the above estimation methods and transmission electron microscopy images. In addition, μ-Raman spectra were recorded for each material, estimating the mean crystallite size for comparison by means of a phonon confinement model.
11 July 2018 in The Journal of Physical Chemistry C
We report the complex refractive index of methylammonium lead iodide (CH3NH3PbI3) perovskite thin films obtained by means of variable angle spectroscopic ellipsometry and transmittance/reflectance spectrophotometry in the wavelength range of 190 nm to 2500 nm. The film thickness and roughness layer thickness are determined by minimizing a global unbiased estimator in the region where the spectrophotometry and ellipsometry spectra overlap. We then determine the optical bandgap and Urbach energy from the absorption coefficient, by means of a fundamental absorption model based on band fluctuations in direct semiconductors. This model merges both the Urbach tail and the absorption edge regions in a single equation. In this way, we increase the fitting region and extend the conventional -plot method to obtain accurate bandgap values.
8 January 2019 in Journal of Physics D: Applied Physics
We develop a band-fluctuations model which describes the absorption coefficient in the fundamental absorption region for direct and indirect electronic transitions in disordered semiconductor materials. The model accurately describes both the Urbach tail and absorption edge regions observed in such materials near the mobility edge in a single equation with only three fitting parameters. An asymptotic analysis leads to the universally observed exponential tail below the bandgap energy and to the absorption edge model at zero Kelvin above it, for either direct or indirect electronic transitions. The latter feature allows the discrimination between the absorption edge and absorption tails, thus yielding more accurate bandgap values when fitting optical absorption data. We examine the general character of the model using a dimensionless joint density of states formalism with a quantitative analysis of a large amount of optical absorption data. Both heavily doped p-type GaAs and nano-crystalline Ga 1-x Mn x N, as examples for direct bandgap materials, as well as amorphous Si:H x , SiC:H x and SiN x , are modeled successfully with this approach. We contrast our model with previously reported empirical models, showing in our case a suitable absorption coefficient shape capable of describing various distinct materials while also maintaining the universality of the exponential absorption tail and absorption edge.
The complex refractive indices of formamidinium cesium lead mixed-halide [FA0.83Cs0.17Pb(I1–xBrx)3] perovskite thin films of compositions ranging from x = 0 to 0.4, with both flat and wrinkle-textured surface topographies, are reported. The films are characterized using a combination of variable angle spectroscopic ellipsometry and spectral transmittance in the wavelength range of 190 nm to 850 nm. Optical constants, film thicknesses and roughness layers are obtained point-by-point by minimizing a global error function, without using optical dispersion models, and including topographical information supplied by a laser confocal microscope. To evaluate the bandgap engineering potential of the material, the optical bandgaps and Urbach energies are then accurately determined by applying a band fluctuation model for direct semiconductors, which considers both the Urbach tail and the fundamental band-to-band absorption region in a single equation. With this information, the composition yielding the optimum bandgap of 1.75 eV for a Si-perovskite tandem solar cell is determined.