One of the key measures of cutting tool efficiency in machining processes is tool wear. In recent decades, numerical modeling of this phenomenon—primarily through finite element cutting models—has gained increasing importance. A crucial requirement for the reliable application of such models is the selection of an appropriate friction model, which strongly affects the accuracy of wear predictions. However, choosing the friction model type and its parameters remains a nontrivial challenge. This paper examines the effect of different friction model types and their parameters on the Archard and Usui wear model indicators, as well as on the main cutting process characteristics: cutting force components, temperature in the primary cutting zone, contact length between the tool rake face and the chip, shear angle, and chip compression ratio. To evaluate their impact on predicted tool wear—expressed qualitatively through the wear indicators of the aforementioned models—several widely used friction models implemented in commercial FEM software were applied: the shear friction model, Coulomb friction model, hybrid friction model, and constant tau model. The simulated values of these cutting process characteristics were then compared with experimental results.
Якість оброблюваних поверхонь деталей залежить від кінематики процесу різання, режиму обробки, конструктивних та геометричних параметрів різального інструмента тощо. Відомі конструкції торцевих фрез, оснащених надтвердими матеріалами, для фінішної обробки площин, визначено режими їх експлуатації та можливості забезпечення необхідної якості обробки. Застосування ступінчастих торцевих фрез, на відміну від звичайних конструкцій фрез, дозволяє забезпечити формування обробленої поверхні різальним елементом, який розміщений у радіальному напрямі на найменшій відстані від осі фрези, а в осьовому – з найбільшим вильотом відносно торця корпуса фрези. При цьому особливу увагу необхідно приділяти питанням стабілізації положення формоутворюючого різального елемента і впливу сил різання на пружний відтиск інструменту від поверхні заготовки. У роботі авторами розглянуто процес торцевого ступінчастого фрезерування конструкційних матеріалів однозубою та багатозубою торцевою ступінчастою фрезою з пружним переміщенням формоутворюючого ножа та з жорстким його закріпленням. У результаті проведених досліджень удосконаленої конструкції торцевої ступінчастої фрези було встановлено, що пружне закріплення формоутворюючого різального елемента, який базується відносно нерухомо закріпленого на корпусі верстата копірі, дозволяє виключити передачу деформацій корпусу фрези під час різання чорновими різальними елементами. Це дозволяє стабілізувати положення формоутворюючого різального елемента та ізолювати його від впливу складової сили різання PY, яка виникає на попередніх чорнових різальних елементах та має змінну величину на ділянках дуги контакту формоутворюючого різального елемента з заготовкою. Запропоновано удосконалену конструкцію ступінчастої торцевої фрези з виконанням пружного контакту формоутворюючого різального елемента з нерухомо закріпленим на корпусі верстата копіром. Отримані результати дослідження підтверджують можливості підвищення якості шляхом розробки нових конструкцій фрез, які б забезпечували необхідні показники мікрогеометрії оброблених поверхонь.
5 February 2025 in Eastern-European Journal of Enterprise Technologies
The object of the study is the aerodynamic resistance of a main road train and its influence on the efficiency of the transportation process. Reducing the aerodynamic resistance of road trains is an important problem, since fuel consumption and transportation efficiency depend on it. A 2 % reduction in aerodynamic drag reduces fuel consumption by 1 %. Reduction of aerodynamic resistance is achieved by using special aerodynamic devices. But their use creates a number of problems – an increase in the weight of the road train and its overall dimensions, etc. It is assumed that by choosing a rational distance between the cab and the semi-trailer of the road train, it is possible to significantly reduce fuel consumption. The obtained results show that the total aerodynamic resistance of the road train significantly depends on the distance between the driver’s cabin and the semi-trailer. This is explained by the fact that in the space between the cabin and the semi-trailer, vortices of the air flow occur, which leads to an increase in aerodynamic resistance. The resulting dependence of excess pressure in the space between the cabin and the semi-trailer on the distance between them makes it possible to determine two ranges of distances where this pressure will be minimal. In contrast to known studies, the results of the modeling make it possible to establish a rational distance between the cab and the semi-trailer of the road train from the point of view of obtaining the minimum total aerodynamic resistance. However, changing the distance between the cab and the semi-trailer can affect the controllability and stability of the road train. The obtained results can be used in the development of semi-trailer structures, which will ensure a reduction of the total aerodynamic resistance of road trains. And this will lead to a decrease in fuel consumption for the transportation process
26 May 2025 in Herald of Khmelnytskyi National University. Technical sciences
Machining flat surfaces on parts made from high-strength materials is predominantly carried out using face mills, whose design solutions can differ significantly from one another. A key factor in selecting the tool is the physical and mechanical characteristics of the workpiece material: depending on the method of heat treatment, chemical composition, carbon content, and the presence of alloying elements, hardness and wear resistance can vary considerably. This article presents a modern approach to milling high-strength materials by using cutting tools equipped with cubic boron nitride (CBN). This material is known for its high hardness and thermal stability, making it versatile for cutting various alloys, including cast irons, hardened steels with high hardness, and other high-strength materials subjected to heavy loads. Within the scope of this work, the designs of contemporary face mills and replaceable cutting inserts from leading manufacturers are examined, alongside the optimal cutting parameters that ensure efficient machining with CBN tools. The paper compares offerings from the global cutting-tool market for processing hard-to-machine materials. A review of both domestic and international scientific publications on the wear resistance of cutting inserts revealed that round inserts often exhibit better wear resistance compared to other shapes (such as triangular or square). Advanced developments by major cutting-tool manufacturers - Sandvik Coromant and Seco Tools - are discussed, focusing on the distinctive features of tool design and geometry. The primary emphasis is placed on assessing the efficiency of various face mill and insert configurations when machining high-strength steels (HRC 45+). Alongside theoretical explanations of the advantages of CBN (high hardness, chemical inertness, and heat resistance), the article presents experimental data and test results from real manufacturing conditions. Recommendations are provided for selecting cutting speeds, feeds, and depths of cut for different types of face mills and inserts from Sandvik Coromant and Seco Tools.