30 December 2024 in TECHNICAL SCIENCES AND TECHNOLOGIES
Presented in the article information is an overview. It discusses residual stresses occurred in the surface during face milling. Face milling is one of the most effective machining processes that provides high accuracy and quality of flat surfaces of products. However, this process is accompanied by the occurrence of internal residual stresses. They can be either compressive or tensile. Tensile stresses can negatively affect the performance of products and should be avoided. This article presents an analysis of research results that describe the mechanisms of formation and prediction of residual stresses during milling, as well as methods for their detection and other auxiliary control methods. An analysis of recent research and publications has shown that the mechanism of residual stress formation and its level during face milling depends on many factors, such as the type of tool material, cutting modes, and material properties of the workpiece. However, the influence of the interaction of these factors, the nature of residual stresses in the material microstructure, and ways to effectively manage them to ensure the desired characteristics of finished products remain insufficiently studied. The purpose of the article is to study the mechanisms of internal stress formation and their level as a result of face milling of flat surfaces. It has been established that for most tool materials, tensile residual stresses are formed at low cutting speeds at high cutting forces. At medium cutting speeds, maximum cutting forces increase the plastic deformation, contributing to the formation of compressive residual stresses in deeper layers, but can increase the risk of surface damage. At high cutting speeds, a decrease in residual stresses was found and they moved to a neutral state. Increasing the feed rate resulted in higher forces and, as a result, tensile residual stresses. Tool wear increased the force. As a result, the resulting residual stresses changed from compressive to tensile, which increased as the tool wore.
30 December 2024 in TECHNICAL SCIENCES AND TECHNOLOGIES
The article discusses innovative methods and technologies for face milling of hard-to-machine materials using polycrystalline cubic boron nitride (PCBN) tools. Special attention is paid to the analysis of the efficiency and durability of cutting tools equipped with superhard inserts, as well as to issues related to the optimisation of the milling process to achieve high quality and precision of the machined surface. The influence of various technological parameters on the stability and productivity of the milling process, as well as the wear characteristics of the cutting elements of the tool, are considered. Special attention is given to the comparison of the properties and characteristics of tool materials, in particular PCBN, with traditional cutting tool materials, demonstrating the advantages of using PCBN for machining difficult-to-machine materials. The results of analytical studies highlight the advantages of using PCBN tools over other tool materials. Recommendations are given for the selection of optimum cutting modes in order to increase the productivity of machine part production and the economic efficiency of the manufacturing process.
26 May 2025 in Herald of Khmelnytskyi National University. Technical sciences
Machining flat surfaces on parts made from high-strength materials is predominantly carried out using face mills, whose design solutions can differ significantly from one another. A key factor in selecting the tool is the physical and mechanical characteristics of the workpiece material: depending on the method of heat treatment, chemical composition, carbon content, and the presence of alloying elements, hardness and wear resistance can vary considerably. This article presents a modern approach to milling high-strength materials by using cutting tools equipped with cubic boron nitride (CBN). This material is known for its high hardness and thermal stability, making it versatile for cutting various alloys, including cast irons, hardened steels with high hardness, and other high-strength materials subjected to heavy loads. Within the scope of this work, the designs of contemporary face mills and replaceable cutting inserts from leading manufacturers are examined, alongside the optimal cutting parameters that ensure efficient machining with CBN tools. The paper compares offerings from the global cutting-tool market for processing hard-to-machine materials. A review of both domestic and international scientific publications on the wear resistance of cutting inserts revealed that round inserts often exhibit better wear resistance compared to other shapes (such as triangular or square). Advanced developments by major cutting-tool manufacturers - Sandvik Coromant and Seco Tools - are discussed, focusing on the distinctive features of tool design and geometry. The primary emphasis is placed on assessing the efficiency of various face mill and insert configurations when machining high-strength steels (HRC 45+). Alongside theoretical explanations of the advantages of CBN (high hardness, chemical inertness, and heat resistance), the article presents experimental data and test results from real manufacturing conditions. Recommendations are provided for selecting cutting speeds, feeds, and depths of cut for different types of face mills and inserts from Sandvik Coromant and Seco Tools.