Different factors affect solar photovoltaic (PV) systems by decreasing input energy and reducing the conversion efficiency of the system. One of these factors is the effect of snow cover on PV panels, a subject lacking sufficient academic research. This paper reviews and compares current research for snow removal in solar PV modules. Additionally, this paper presents the design, analysis and modelling of a smart heating system for solar PV Electric Vehicle (EV) charging applications. The system is based on a bidirectional DC-DC converter that redirects the grid/EV-battery power into heating of the solar PV modules, thus removing snow cover, as well as providing the function of MPPT when required to charge the EV battery pack. A control scheme for each mode of operation was designed. Subsequently, a performance evaluation by simulating the system under various conditions is presented validating the usefulness of the proposed converter to be used in solar PV systems under extreme winter conditions.
Over the last two decades, motor drives comprising of power electronic converters and advanced electric machines have deeply penetrated into the transportation sector, where new technologies are explored, in order to electrify various modes of transportation systems. Electric transportation puts much greater demand on power electronics than conventional fossil fuel powered automobiles. In many cases (e.g., hybrid internal combustion/electric drive vehicles), optimized power electronics suites are essential. Significant advances in power electronics and motor drives have helped reduce the cost and improve the efficiency of electric vehicles (EVs). This paper reviews on evolution and advancements of permanent magnet synchronous motor (PMSM) drive systems for EVs. The paper also discusses on multiphase PMSMs and multi-motor drive systems which can be revolutionized for future electric transportation applications.
20 December 2018 in IEEE Transactions on Industrial Electronics
A multilevel drive can be realized by using open-ended machine, fed from dual two-level inverters. The topology supplied from isolated DC sources is suitable for transportation electrification. In vehicular systems, it is essential that the isolated DC sources, comprising of battery packs, should discharge uniformly and maintain balanced DC voltage at the DC-link terminal. A simple carrier-based pulse width modulation (CBPWM) technique is presented in this paper, which can effectively regulate the power drawn between the two two-level inverters while maintaining the multilevel operation of the drive. The modulation technique can balance the instantaneous state of charge (SOC) of independent battery packs and dynamically equalize the power flow from the two inverters, based on drive requirement. This will enhance the reliability of the propulsion system in electric vehicles. The operation of the proposed PWM technique has been validated through detailed simulation and experimental tests.
In the industrial production stage of a drive, its control algorithm must be tested for its validity with real machine. Testing with real machine could pose some serious challenges. During the testing, if the control algorithm starts behaving unexpectedly, it may cause serious damage to the real machine or drive. Such hazardous operating conditions can be avoided by replacing a real machine with a power electronic converter based `Virtual Machine' (VM) test-bench. The VM can be designed to allow the device under test (DUT) to be tested at actual power with the help of a power electronic converter test setup and the motor model. The VM controls the current drawn from the DUT to match with that of estimated by the motor model. The existing VM system comprises of AC-DC followed by DC-AC converter, increasing the number of converter stages in the system. In addition, both the converters require independent control which increases the control complexity. This multistage conversion stage can be eliminated by replacing AC-DC-AC emulator with AC-DC converter supplied by common DC bus to DUT and VM both. Taking into account, this paper proposes a novel single-stage, three-phase bi-directional AC-DC converter topology suitable for VM system.
The critical components in electric vehicle (EV) propulsion system are the traction inverter and motor. For better performance of the EV, it is important to operate traction inverter/motor at optimal efficiency points over the entire drive cycle. The significant advances in pulse width modulation (PWM) techniques has helped to improve the efficiency of the traction drive. Hence this paper aims at the modeling of the traction inverter with different PWM techniques, over different city driving schedules and analyze the energy losses in the semiconductor devices. The paper presents the thermal model based analysis of DC/AC inverter considering the conduction and switching losses for both insulated gate bipolar transistor (IGBT) and antiparallel diodes as a switch. An induction motor driving a medium-sized EV, has been modeled in the PLECS software. The energy loss calculation is carried out based on device characteristics. The losses are observed for both cold start and hot starts, based on the heat sink temperature.
An industrial drive testing, with a ‘real-machine’ can pave way, for some serious issues to test-bench and motor. A slight disturbance in control logic amid testing, can damage the physical machine or drive. Such dangerous testing conditions can be avoided by supplanting real motor with a power electronic converter based ‘Motor Emulator’ (ME) test-bench system. The conventional ME comprises of two-stage three-phase AC-DC-AC conversion with first-stage AC-DC as emulator and second-stage DC-AC as regenerating unit. This two-stage power conversion, require independent control algorithm, burdening control complexity as well as the number of power electronic switches are quite significant. Hence, to economize and downsize conventional multistage ME system, this paper experimentally validates a common DC-bus-configured ME system with only the AC-DC regenerative emulator stage. A virtually isolated bidirectional two-level three-phase AC-DC converter is proposed as the regenerative emulator converter in a common DC-Bus-configured ME system. The Proposed converter’s operating principle along with mathematical design and control strategy are also presented. To validate the operation of the proposed converter as a common DC-bus-configured emulator, a permanent magnet synchronous motors (PMSM) of 7.5 kW is emulated and its experimental results are presented here.