1 July 2020 in Physics of Plasmas
Pulsed power accelerators compress electrical energy in space and time to provide versatile experimental platforms for high energy density and inertial confinement fusion science. The 80-TW “Z” pulsed power facility at Sandia National Laboratories is the largest pulsed power device in the world today. Z discharges up to 22 MJ of energy stored in its capacitor banks into a current pulse that rises in 100 ns and peaks at a current as high as 30 MA in low-inductance cylindrical targets. Considerable progress has been made over the past 15 years in the use of pulsed power as a precision scientific tool. This paper reviews developments at Sandia in inertial confinement fusion, dynamic materials science, x-ray radiation science, and pulsed power engineering, with an emphasis on progress since a previous review of research on Z in Physics of Plasmas in 2005.
6 January 2017 in Journal of Applied Physics
Uniaxial strain, plate-on-plate impact experiments were performed on cold-rolled Ni/Al multilayer composites and the resulting Hugoniot was determined through time-resolved measurements combined with impedance matching. The experimental Hugoniot agreed with that previously predicted by two dimensional (2D) meso-scale calculations [Specht et al., J. Appl. Phys. 111, 073527 (2012)]. Additional 2D meso-scale simulations were performed using the same computational method as the prior study to reproduce the experimentally measured free surface velocities and stress profiles. These simulations accurately replicated the experimental profiles, providing additional validation for the previous computational work.
22 March 2022 in Journal of Applied Physics
Uniaxial strain, reverse-ballistic impact experiments were performed on wrought 17-4 PH H1025 stainless steel, and the resulting Hugoniot was determined to a peak stress of 25 GPa through impedance matching to known standard materials. The measured Hugoniot showed evidence of a solid–solid phase transition, consistent with other martensitic Fe-alloys. The phase transition stress in the wrought 17-4 PH H1025 stainless steel was measured in a uniaxial strain, forward-ballistic impact experiment to be 11.4 GPa. Linear fits to the Hugoniot for both the low and high pressure phase are presented with corresponding uncertainty. The low pressure martensitic phase exhibits a shock velocity that is weakly dependent on the particle velocity, consistent with other martensitic Fe-alloys.
28 December 2021 in Journal of Applied Physics
We measured the Hugoniot, Hugoniot elastic limit (HEL), and spallation strength of laser powder bed fusion (LPBF) AlSi10Mg via uniaxial plate-impact experiments to stresses greater than 13 GPa. Despite its complex anisotropic microstructure, the LPBF AlSi10Mg did not exhibit significant orientation dependence or sample-to-sample variability in these measured quantities. We found that the Hugoniot response of the LPBF AlSi10Mg is similar to that of other Al-based alloys and is well approximated by a linear relationship: . Additionally, the measured HELs ranged from 0.25 to 0.30 GPa and spallation strengths ranged from 1.16 to 1.45 GPa, consistent with values reported in other studies of LPBF AlSi10Mg and Al-based alloys. Strain-rate and stress dependence of the spallation strength were also observed.
27 October 2016 in Journal of Dynamic Behavior of Materials
12 December 2022 in Journal of Applied Physics
We uniaxially and shocklessly compressed an additively manufactured aluminum alloy, laser powder bed fusion (LPBF) AlSi10Mg, to peak stresses ranging from 4.4 to 14.8 GPa at peak strain rates on the order of via a series of magnetic loading experiments to measure the principal isentrope, yield strength, and shear modulus as a function of material orientation and applied stress. We did not observe significant anisotropy in any of the measured quantities. We found that the principal isentrope, within the uncertainty and up to our peak stress, overlaps the material’s Hugoniot. We measured yield strengths and shear moduli ranging from 0.28 to 0.81 GPa and 36 to 52 GPa, respectively. Our results indicate that LPBF AlSi10Mg behaves similarly to wrought Al alloys under quasi-isentropic compression.