Sneha Prabha Narra

Sneha Prabha Narra

Auto-generated profile, based on publicly available information

Sneha Prabha Narra

Mechanical Engineering Department, Carnegie Mellon University, 5000 Forbes Avenue, Pittsburgh, 15213, PA, USA

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 January 2017 in JOM
Verified
Journal Article
Closed access
PDF file
RCRoss Cunningham
Ross Cunningham
SNSneha P. Narra
Sneha P. Narra
CMColt Montgomery
Colt Montgomery
JBJack Beuth
Jack Beuth
ARA. D. Rollett
A. D. Rollett

4 January 2016 in JOM
Verified
Journal Article
Closed access
PDF file
MTMing Tang
Ming Tang
Petrus Christiaan PistoriusPetrus Christiaan Pistorius
Petrus Christiaan Pistorius
SNSneha Narra
Sneha Narra
JBJack L. Beuth
Jack L. Beuth

11 August 2020 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
Ziheng WuZiheng Wu
Ziheng Wu
SNSneha Prabha Narra
Sneha Prabha Narra
ARAnthony D. Rollett
Anthony D. Rollett
Although additive manufacturing (AM) is becoming increasingly popular for various applications, few studies have addressed design and potential problems in thin wall fabrication for the laser powder bed fusion (LPBF) process. In the LPBF process, rapid cooling induces thermal shrinkage, which in turn, results in high residual stress and complicates thin wall fabrication. The minimum wall thickness is limited by the parameters and machine settings while the dimensional accuracy is controlled by the powder size, scan strategy, and part geometry. The ability to fabricate thin-wall components is important for applications such as heat exchangers (HX). This study explores the performance of the LPBF process by fabricating thin walls with extreme geometries in different processing conditions and alloys using an EOS M290 LPBF machine. Results show that the material, part design, and scanning strategy contribute to the variation in thin wall dimensions. A maximum inclination angle of 60° and a minimum wall thickness of ~ 100 μm in Ti-6Al-4V, Inconel 718, and AlSi10Mg were achieved using optimized part design and processing conditions. The effects of part design and material on the thermal distortion and surface finish of thin walls were also investigated leading to a discussion on how the scan mode assigned by the EOS software affects design and fabrication. Additionally, synchrotron-based X-ray micro-tomography (μSXCT) was utilized to quantify the porosity in thin-wall structures and to correlate it with the integrity of the structures. Comprehensive design guidelines presented in this work can increase the success rate of fabricating thin-wall geometries.

19 January 2016 in JOM
Verified
Journal Article
Closed access
PDF file
RCRoss Cunningham
Ross Cunningham
SNSneha P. Narra
Sneha P. Narra
TOTugce Ozturk
Tugce Ozturk
JBJack Beuth
Jack Beuth
ARA. D. Rollett
A. D. Rollett

10 May 2017 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Open access
PDF file
RLRianne E. Laureijs
Rianne E. Laureijs
JRJaime Bonnín Roca
Jaime Bonnín Roca
SNSneha Prabha Narra
Sneha Prabha Narra
CMColt Montgomery
Colt Montgomery
JBJack L. Beuth
Jack L. Beuth
EFErica R. H. Fuchs
Erica R. H. Fuchs
Additive manufacturing (AM) is increasingly of interest for commercial and military applications due to its potential to create novel geometries with increased performance. For additive manufacturing to find commercial application, it must be cost competitive against traditional processes such as forging. Forecasting the production costs of future products prior to large-scale investment is challenging due to the limits of traditional cost accounting's ability to handle both the systemic process implications of new technologies and the cognitive biases in humans' additive and systemic estimates. Leveraging a method uniquely suited to these challenges, we quantify the production and use economics of an additively manufactured versus a traditionally forged GE engine bracket of equivalent performance for commercial aviation. Our results show that, despite the simplicity of the engine bracket, when taking into account the part redesign for AM and the associated lifetime fuel savings of the additively designed bracket, the additively manufactured part and design is cheaper than the forged one for a wide range of scenarios, including at higher volumes of 2000–12,000 brackets per year. Opportunities to further reduce costs include accessing lower material prices without compromising quality, producing vertical builds with equivalent performance to horizontal builds, and increasing process control so as to enable reduced testing. Given the conservative nature of our assumptions as well as our choice of part, these results suggest that there may be broader economic viability for additively manufactured parts, especially when systemic factors and use costs are incorporated.

29 December 2023 in Acta Materialia
Verified
Journal Article
Open access
WTWilliam Frieden Templeton
William Frieden Templeton
SHShawn Hinnebusch
Shawn Hinnebusch
SSSeth T. Strayer
Seth T. Strayer
ATAlbert C. To
Albert C. To
PPP. Chris Pistorius
P. Chris Pistorius
SNSneha Prabha Narra
Sneha Prabha Narra