Rehan Ahmed

Rehan Ahmed

Auto-generated profile, based on publicly available information

Rehan Ahmed

Department of Computer and Software Engineering, Information Technology University, Lahore, Pakistan

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 October 2022 in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
Verified
Journal Article
Closed access
RARehan Ahmed
Rehan Ahmed
SDStefan Draskovic
Stefan Draskovic
Lothar ThieleLothar Thiele
Lothar Thiele
Energy harvesting is increasingly used as a long-term energy supply for the Internet of Things, wireless sensor networks, and cyber-physical systems. However, the challenge of mitigating the variability of energy harvesting sources needs to be addressed before ubiquitous adoption can happen. Otherwise, an unreliable operation of devices with frequent shutdowns during times of energy scarcity would be encountered. One finds probabilistic performance metrics helpful in designing power management solutions for the long-term operation of energy harvesting nodes. These metrics include the probability of battery depletion, expected energy consumption, expected battery level, and similar. This article proposes a stochastic modeling technique and corresponding analysis which can provide such metrics. Our advanced analysis is based on Markov chains. By modeling harvested energy with random variables, new and existing energy management policies are analyzed and compared. We propose an adaptive energy management strategy inspired by mixed-criticality systems. In the proposed strategy, the system can degrade or drop less essential tasks in real time to ensure a graceful degradation of service in adverse harvesting conditions. We compare the proposed energy management approach to several existing alternatives. To this end, we conduct extensive simulations for indoor and outdoor environments, where our strategy matches or outperforms the state of the art. Initial results also validate the high precision of our stochastic model and analysis in comparison to simulations using real-world data.

11 March 2026 in IEEE Geoscience and Remote Sensing Letters
Verified
Journal Article
Closed access
SHSaad Bin Hammad
Saad Bin Hammad
ENEhtasham Naseer
Ehtasham Naseer
MSMuhammad Adnan Siddique
Muhammad Adnan Siddique
RARehan Ahmed
Rehan Ahmed
This paper presents a hybrid CNN-Vision Transformer architecture for landslide segmentation in complex land-scapes, such as Pakistan’s northern mountains. The land cover heterogeneity in this region makes landslide segmentation in multi-spectral optical imagery a particularly challenging task. Our approach combines a CNN encoder for multi-modal data processing with a Data-efficient Image Transformer (DeiT) backbone and attention-based feature fusion. The annotation-guided workflow refines the initial 1,072 annotations and uses probability maps to identify missed landslides, yielding 1,352 positive landslide samples and 1,978 negatives. This constitutes the first comprehensive Pakistan landslide dataset. The hybrid model achieves validation correlation of 0.4794, demonstrating 16.64% improvement over CNN-only (0.411) and 10.79% over DeiT-only (0.4327). Statistical decision boundaries derived from Otsu demonstrate operational readiness for disaster management while introducing an efficient annotation framework applicable to other geospatial applications.

19 May 2026 in IEEE Access
Verified
Journal Article
Open access
MMMuhammad Mudasser Latif Minhas
Muhammad Mudasser Latif Minhas
NENofal Elahi
Nofal Elahi
RARehan Ahmed
Rehan Ahmed
Junaid ArshadJunaid Arshad
Junaid Arshad
RHRehan Hafiz
Rehan Hafiz
MZMuhammad Zaman
Muhammad Zaman
Road traffic accidents, congestion, and inefficient mobility cause significant loss of life, time, and economic productivity worldwide, driving growing demand for Intelligent Transportation System (ITS). However, high cost of ITS impedes its wide-scale adoption. There is a need for low-cost, open source Vehicle-to-Infrastructure (V2I) hardware to enable wide research adoption and real-world deployment. This paper presents the complete design, implementation, and field evaluation of an experimental On Board Unit (OBU) and Road Side Unit (RSU) for V2I communication. Both devices are built from commercial off-the-shelf components. The unit cost is approximately $117 (OBU) and $80 (RSU). This is substantially lower compared to commercial Dedicated Short Range Communication (DSRC) based devices. Point-to-point range tests demonstrated minimum packet delivery rate of 81% at distances up to 485m under obstructed, non-line-of-sight conditions. A two-OBU, two-RSU testbed was subsequently deployed at a University Campus. Field measurements confirmed the feasibility of the developed design as a low-cost V2I research/testbed platform. OBU⇌RSU round-trip latency was observed to be less than 300 ms. This makes the proposed design suitable for prototype V2I applications such as signal advisory, road-hazard alerts, and traffic monitoring. The Packet Delivery Ratio (PDR) for the nominal OBU–RSU pair was observed to be 78% for OBU→RSU and 73% for RSU→OBU. This demonstrates consistent low-latency communication for prototype V2I applications.

1 January 2026 in IEEE Geoscience and Remote Sensing Letters
Verified
Journal Article
Closed access
MAMuhammad Nauman Arshad
Muhammad Nauman Arshad
MSMuhammad Adnan Siddique
Muhammad Adnan Siddique
ENEhtasham Naseer
Ehtasham Naseer
RARehan Ahmed
Rehan Ahmed
IHIqra Hassan
Iqra Hassan
MAMuhammad Farooq Ahmed
Muhammad Farooq Ahmed

1 January 2026 in Journal of Sensors
Verified
Journal Article
Open access
MFMuhammad Farhan
Muhammad Farhan
SSSamra Shaheen
Samra Shaheen
MAMunawar Arshad
Munawar Arshad
ATAbdul Hanan Taqi
Abdul Hanan Taqi
MZMuhammad Hamza Zulfiqar
Muhammad Hamza Zulfiqar
MMMuhammad Qasim Mehmood
Muhammad Qasim Mehmood
Paralysis impacts 5.6 million people worldwide and significantly increases the risk of developing pressure ulcers resulting from continuous skin pressure over bony areas. Prolonged pressure on the skin of paralyzed patients deteriorates tissue and raises the rate of bedsores. Our study aims to reduce the incidence of pressure ulcers by developing pressure sensors, healthcare protocols, alert systems, and patient positioning strategies. We fabricate a flexible, eco‐friendly, long‐lasting, and cost‐effective capacitive pressure sensor (CPS) specifically designed for preventing pressure ulcers in paralyzed patients. To maintain precise deposition of a conductive ink under a shadow mask on both sides of the mattress, a laser cutter is used to cut square holes in the sticker under pressure points, which act like parallel‐plate capacitors. The conductive ink is then sintered, and the shadow mask is removed. The system supports continuous pressure monitoring by integrating a Bluetooth module for wireless data transmission, a buzzer alarm for instant alerts, and an Arduino‐based data acquisition unit. The CPS detects pressure changes and triggers an alarm when pressure thresholds are exceeded. To validate the sensors, we used a two‐axis force platform to characterize the CPS. CPS has a recovery time of 0.26 s, a quick response time of 0.5 s, a sensitivity of 0.266 kPa −1 , and a pressure range of 0.625–75 kPa and has been observed to operate over 23,000 measurements for long‐term stability, demonstrating its potential for integration into continuous pressure monitoring and pressure‐ulcer risk assessment applications. It addresses the basic problems of affordability and durability, which may enhance patient care and reduce healthcare expenditure.