1 December 2017 in IEEE Transactions on Magnetics
The near-field communication (NFC) technique finds wide applications in many aspects of modern life, e.g., contactless payment systems or authentication. Regardless of the application, typically, the requirements on the antenna structure are manifold. Frequently, limitations in the available space make the antenna design quite challenging. Beside geometrical limitations, also the matching of the antenna structure to the analog front end of the NFC transponder IC has to be taken into account. Furthermore, the NFC antenna together with the connected IC has to fulfill specific standardized values. In this paper, the optimization of an NFC antenna structure including the needed matching circuit in the multi-objective sense is proposed. Due to its simplicity and the consequently reduced computational effort, the partial-element electric circuit (PEEC) method is applied to carry out the needed field computation in the so-called NFC operating volume. Furthermore, the PEEC method offers the possibility of simply connecting lumped components to the antenna structure within the numerical analyses, which enables the optimization of the matching circuit parallel to the optimization of the antenna structure. The optimization relies on a stochastic optimization strategy, namely, the firefly algorithm (FFA). In this paper, an extended version of the general FFA is applied.
28 November 2017 in IEEE Transactions on Magnetics
Transformer windings, as resonant systems, respond to impulse excitation by oscillating voltages and currents. In this paper, a detailed transient circuit analysis of an auto-transformer exposed to a full and a chopped standard lightning impulse has been performed, taking into account each single turn of the two windings. The corresponding inductance and capacitance matrices used in the circuit analysis are obtained by finite-element method (FEM)-calculations. To get the resistances of the turns, eddy currents have to be considered. Since the turns (continuously transposed conductors) consist of a certain number of single strands to keep the eddy current losses low, an appropriate eddy current calculation by FEM has to be performed, taking account of each single strand of the turns. The resulting resistances of the turns are typically several hundred times higher than the respective dc resistances. This has a significant influence on the damping behavior of the high-frequency oscillations of the system.
22 April 2019 in IEEE Letters on Electromagnetic Compatibility Practice and Applications
Models of overvoltage protection devices, such as transient voltage suppressor diodes (TVS-diodes) are largely available in circuit analyzer tools. For this letter, the widely used circuit simulation tool LTspice was employed and during the course of investigating the simulation of such protection devices in the context of electrical fast transient phenomena, especially electrical fast transients (EFT/BURST) and electrostatic discharge (ESD), certain existing diode-model types can present inaccuracies when predicting the disturbances generated by those devices. Presumably this is the case regarding the model of the junction capacitances, especially for the cutoff region, since the implementation follows a linear extrapolation and therefore differs from the real behavior of the protection device under test. This letter deals with the investigation of a simulation setup and occurring limitations for the analysis of the transient behavior. It should give some encouragement to always consider given model-limitations and how they can affect the simulated results and also if the applicability for certain investigations is provided.
9 January 2020 in IEEE Transactions on Magnetics
The field regions around antennas are distinguished through the properties of the electromagnetic field. The knowledge of the boundaries between these regions is very important for e.g. measurement engineers or in the numerical simulation to ensure a proper behavior of their results. In the present work the validity of the boundaries suggested from the literature has been analyzed using error estimations for different properties of the electromagnetic field. Analyses are conducted on dipole antennas, loop antennas as well as on Yagi-Uda arrays with various dimensions. In addition, different concepts are introduced allowing the definition of a more convenient boundary between the field regions. The proposed rules satisfy the IEEE standard definitions in a better way. For the numerical computations a one dimensional Method of Moments is applied.
4 September 2017 in COMPEL - The international journal for computation and mathematics in electrical and electronic engineering
Purpose: The purpose of this paper is the modelling and estimation of inrush currents while energising power devices under no load conditions. An analytical representation of the nonlinear B-H curve serves for considering the hysteresis behaviour in the numerical model. Design/methodology/approach: The model is implemented into a standard finite element formulation to compute transient problems. Findings: Inrush currents behave like faults in power distribution facilities. Its prior estimation helps to distinguish between operating conditions and faults. Research limitations/implications: The magnetic cores may become extremely magnetised. At such high material saturations, the material characteristics are not measurable accurately. Hence, the results depend on the extrapolation of the B-H curves. Originality/value: The use of first-order reversal curves within the major hysteresis loops helps in a convenient way to estimate peak and shape of the inrush currents.
19 January 2017 in IEEE Transactions on Magnetics
A major design criterion of wireless communication devices is the matching between the impedance of the analog frontend and the input impedance of the antenna structure. Especially for passive communication systems, the matching is essential to ensure good performance. Numerical design tools are typically utilized in the antenna design process to determine the antenna impedance. Additionally, measurements on prototype designs are carried out to verify the simulation results. Frequently, vector network or impedance analyzers are used to measure the impedance of the antenna design. Regardless of the measurement device in use, a connection between it and the device under test has to be established. In this paper, the interaction between the interconnection structure and the antenna under test is investigated. Special attention is paid to the influence of the interconnection structure on the antenna impedance obtained. The investigations are carried out on a typical test problem by numerical field simulations by means of the finite-element method.