Integrated smart power devices gain more and more importance in the field of automotive systems. In addition to power transistors such devices usually contain several integrated diagnostic and protection functions. In the event of a fault these functions enable the connected control unit to react appropriately and to protect the application and thus the people. Smart power devices are often responsible for important tasks within a vehicle and are nowadays more and more used to substitute conventional elements like fuses, relays and switches. During the operation they are often exposed to harsh environmental conditions such as high operating temperatures, mechanical stress, etc. At the same time different electromagnetic interferences (EMI) may occur, which can affect their normal functionality. Especially in safety-critical applications such as the airbag control module or the Anti-lock Braking System their correct function is very important to avoid dangerous operating conditions and to ensure functional safety. Based on EMI investigations on a representative smart power high side switch it is shown in this paper to what degree of electromagnetic interference smart power devices are still able to correctly detect critical fault conditions and remain in their fail-save state. Im Bereich der Leistungselektronik werden in modernen Kraftfahrzeugen zunehmend so genannte ”Smart Power Devices“ eingesetzt. Sie beinhalten neben den Leistungstransistoren meist mehrere integrierte Diagnose- und Schutzfunktionen. Im Fehlerfall ermöglichen diese Funktionen dem angeschlossenen Steuergerät, entsprechend zu reagieren und die Anwendung und damit die Menschen zu schützen. Smart Power Devices sind oft für wichtige Aufgaben innerhalb eines Fahrzeugs verantwortlich und werden heutzutage immer häufiger eingesetzt, um herkömmliche Elemente wie Sicherungen, Relais und Schalter zu ersetzen. Während des Betriebs sind sie oft rauen Umgebungsbedingungen – wie hohen Betriebstemperaturen, mechanischen Belastungen usw. – ausgesetzt. Gleichzeitig können zusätzlich unterschiedliche elektromagnetische Störungen auftreten, welche die normale Funktionalität dieser Geräte beeinträchtigen können. Gerade in sicherheitskritischen Anwendungen wie dem Airbag-Steuermodul oder dem Antiblockiersystem ist ihre korrekte Funktion sehr wichtig, um gefährliche Betriebszustände zu vermeiden und die funktionale Sicherheit zu gewährleisten. Auf der Grundlage von Störfestigkeitsuntersuchungen an einem repräsentativen Smart Power High Side-Schalter wird in diesem Beitrag gezeigt, bis zu welchem Ausmaß an elektromagnetischen Störungen Smart Power Devices kritische Fehlerbedingungen immer noch korrekt erkennen können und somit die funktionale Sicherheit des Kraftfahrzeugs gewährleisten.
Computer aided design and simulations are an integral part in the development process of integrated circuits. In order to evaluate the electromagnetic compatibility (EMC) of integrated circuits in simulation, simulation models of the EMC measurement setup and the EMC measurement device are needed. In this work, an electromagnetic interference (EMI) receiver simulation model is presented. The EMI-reciever simulation model is intended to analyze electromagnetic emission (EME) of integrated circuits from transient simulations. The model is explained in detail and emulates an CISPR-16 conform test receiver. It is implemented using an STFT algorithm, and evaluates simulation output in CISPR Band-B/C/D with peak, average and quasi-peak detector. A quasi-peak detector model for pulsed disturbances is described, that significantly reduces simulation time compared to traditional implementations. The presented EMI-receiver model is verified with different test setups.
4 August 2021 in IEEE Transactions on Electron Devices
In this work, an analysis of the impact of drain field plate (FP) length on the semi-on degradation of AlGaN/GaN high-electron-mobility transistors (HEMTs) is performed. A wafer-level characterization, by means of pulsed stress tests, reveals a faster and more severe decrease of the drain current in the linear region for the samples with longer drain FP. 2-D technology computer-aided design (TCAD) hydrodynamic simulations show that a time and field-dependent hot electrons (HEs) trapping takes place at the passivation/barrier interface. The higher drain current decrease in the longer FP samples can be ascribed to an enhanced HE trapping at the drain FP edge due to a different electric field distribution.
This paper presents a novel converter for boosting the low-voltage output of thermoelectric energy harvesters to power standard electronic circuits. The converter can start up from a fully depleted state of the system off a bipolar ±13 mV input and can boost it to output voltages of up to 5 V. The converter comprises two transformers, one for each polarity that are multiplexed between an oscillator (used during startup) and a flyback converter (used during normal operation). To eliminate leakage currents in the input stage, the unused converter is completely turned off at startup and both converters are automatically shut off if the input power is found to be too low. Measurement results of the converter designed in a 180 nm CMOS process demonstrate a peak end-to-end conversion efficiency of 85% and nearly perfect impedance matching over the full input voltage range. This is the first time that a converter for ultra-low bipolar input voltages achieves the same performance as a unipolar converter.