Regardless of the technology, additive or subtractive, the miniaturization trend is constantly pushing for smaller resolutions. The rise of global challenges in material availability, fabrication in three dimensions (3D), design flexibility and rapid prototyping have pushed additive manufacturing (AM) into the spotlight. Addressing the miniaturization trend, AM has already successfully answered the challenges for microscale 3D fabrication. However, fabricating nano-resolution still presents a challenge. In this review, we will present some of the most reported AM-based technologies capable of nanoscale 3D fabrication addressing resolutions of ≤ 500 nm. The focus is placed on Electrohydrodynamic (EHD) printing (also known as e-jet printing), as EHD printing seems to have the best trade-off when it comes to technique complexity, achievable resolutions, material diversity and potential to scale-up throughput. An overview of the smallest achieved resolutions as well as the most unique use cases and demonstrated applications will be addressed in this work.
Advanced packaging solutions require insulation and passivation materials with exceptional properties which can also fulfill the reliability needs of electronics devices such as MEMS, sensors or power modules. Since bonding (cohesive/adhesive) properties of packaging coatings are very important for reliable functioning of electronics devices, the bonding of aliphatic fluorinate-4 (AF4) parylene coatings was assessed in this work. As there is a lack of data regarding its bonding towards different substrates, pull-off tests of 1.6 and 2.5 μm thick AF4 coatings on silicon (Si) and glass (SiO2) substrates were performed. These showed a clear difference in the pull-off F/s curves between the AF4 coatings on Si and SiO2 substrates. This difference is parameterized by the pull-off energy, which will be presented in this work. To further understand the origin of the distinction in the pull-off energies between the AF4-Si and AF4-SiO2 samples and subsequently the cohesive/adhesive properties, mechanical and structural characterization was conducted on the AF4 coatings, where a clear difference in the E-modulus and crystallinity was observed. The Si and SiO2 wafers were shown to facilitate the CVD growth of the AF4 film distinctively, which likely relates to the divergent thermal properties of the substrates. Understanding of the cohesive/adhesive properties of AF4 coatings on different substrate materials advances the usage of the AF4 in electronics packaging technologies.
Barium hexaferrite BaFe12O19 composition was prepared using the respective powder mixture of metal oxides BaCO3 : 6?Fe2O3 and by performing a solid-state reaction at 1000?C/4h in air. The obtained barium hexaferrite was milled for a prolonged time in the planetary ball mill and agate mill to achieve a fine powder of submicron particle size. The prepared powder was characterized using XRD and SEM techniques.The BaFe12O19 submicron powder was mixed with 2.5 % wt. SiO2 nanopowder as a dopant. After that, the doped barium hexaferrite powder mixture was pressed into small and thin disk samples at 0.2 GPa. The prepared disk samples were sintered at different sintering profiles from 1050?C to 1275?C/2h in air. The sintered samples were also characterized using XRD and SEM. The main electrical properties such as disk capacitance C and resistance R at 1Hz to 100 Hz were measured using a low frequency impedance analyzer. The dielectric permittivity ?r and dissipation factor tg? were calculated from the equivalent disk capacitor electrical schemes. The obtained results were used for observing space charge relaxation effects and colossal permittivity.
1 January 2026 in Processing and Application of Ceramics
NTC thermistors in form of bulk ceramics and thick film, with the nominal composition \mathrm{Ni_{0.5}Cu_{0.2}Zn_{1.0}Mn_{1.3}O_4} , were prepared from fine manganite powder. The finemanganite powder with an average particle size of ~0.5 μm was obtained by calcination of homogeneous mixture of NiO, ZnO, CuO and \mathrm{Mn_2O_3} powders at 900°C for 4 h and subsequently combined planetary and agate milling. Phase composition and morphology of the manganite powder were analysed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Disk-shaped compacts were fabricated by uniaxial pressing at 0.2GPa and sintered at temperatures between 1100 and 1250°C for 2 h. The effects of sintering temperature on density, microstructure and DC electrical resistance were evaluated. Temperature-dependent resistance measurements performed in the range from −30 to 120°C yielded a thermistor constant of B = 2352K. The energy band gap, estimated from the reflectivity knee, was 0.56 eV. Furthermore, a thick-film paste was formulated from the synthesized manganite powder and used to fabricate segmented NTC thermistors. Electrical and thermal measurements, including sheet resistance, confirmed their suitability for further sensor applications.