1 August 2008 in Optical Engineering
Accurate laser damage measurements are more difficult to perform in nonlinear optical crystals than in glasses due to several effects proper to these materials or greatly enhanced in these materials. Before discussing these effects, we address the topic of error bar determination for probability measurements. Error bars for the measured damage probabilities are especially important when testing small and expensive samples like nonlinear crystals, where only few sites are used for each measurement. The mathematical basics for the numerical calculation of probability error bars corresponding to a chosen confidence level are presented. Effects that possibly modify the maximum light intensity obtained by focusing into a biaxial nonlinear crystal are mainly the focusing aberrations and self-focusing. Depending on focusing conditions, position of the focal point in the crystal, beam propagation direction, and polarization, strong aberrations may change the beam profile and drastically decrease the maximum intensity in the crystal. A correction factor based on former theoretical work is proposed for this effect. The characteristics of self-focusing are quickly reviewed for the sake of completeness, and a note on parasitic second harmonic generation is added at the end.
13 July 2012 in Optical Engineering
Multipulse laser-induced damage is an important topic for many applications of nonlinear crystals. We studied multipulse damage in X-cut . Using a 6-ns Nd:YAG laser with a weakly focused beam, a fatigue phenomenon was observed. We addressed whether this phenomenon necessarily implies material modifications. Two possible models were tested, both of them predicting increasing damage probability with increasing pulse number while all material properties are kept constant. The first model, pulse energy fluctuations and depointing, increases the probed volume during multiple pulse experiments. The probability to cause damage thus increases with increasing pulse number; however, this effect is too small to explain the observed fatigue. The second model assumes a constant single-shot damage probability , so a multipulse experiment can be described by statistically independent resampling of the material. Very good agreement was found between the 2000-on-1 volume damage data and this statistical multipulse model. Additionally, the spot size dependency of the damage probability is well described by a precursor presence model. Supposing that laser damage precursors are transient, the presented data explain the experimental results without supposing material modifications.
9 January 2025 in Journal of Applied Physics
The influence of laser polarization on the laser-induced damage threshold of fused silica is presented. Measurements were performed using femtosecond and nanosecond laser pulse durations. The impact of laser polarization on the laser damage varies with laser wavelength. While no difference in UV laser damage was observed between linear and circular polarizations, circular polarization improved the damage resistance of fused silica to infrared and visible laser radiation in comparison with linear polarization. By measuring the femtosecond laser damage of a SiO2 thin film deposited onto a substrate, we show that the ratio between the bandgap of the sample and the photon energy causes the polarization dependent laser damage to change. These experimental findings are explained by considering the photoionization theory for solids.
11 September 2018 in Optical Engineering
A vacuum chamber was designed to study the risk of laser-induced contamination (LIC) on optical payloads integrated on spaceflight missions. In this context, tests were performed with a nanosecond pulsed laser at 355 nm on fused silica substrates under toluene exposure with multiple laser irradiation. Specific experimental procedures are described in order to obtain repeatable results. Finally, series of tests were performed to investigate the onset of the LIC deposition process and its evolution over time. A slight antireflective effect is consistently observed at the onset of the deposition process. We suggest that this is an indication that the LIC deposition process in our experimental conditions starts with a nucleation layer consisting of small dense islands of deposit.
1 September 2022 in Optical Engineering
Lasers in space often suffer from light absorbing deposits forming inside the resonator. This effect is commonly called laser-induced contamination (LIC), and its mechanism can be compared with laser chemical vapor deposition. LIC experiments were carried out in a dedicated vacuum chamber using a q-switched 355-nm laser, hafnia- or silica-coated fused silica samples and contamination by epoxy adhesive outgassing, or toluene vapor in vacuum. The typical deposit formation was observed at different experimental conditions and analyzed by in situ laser-induced fluorescence imaging and ex situ white light interference microscopy. We determined the average growth rate during the first growth stage (bump-shaped growth) and analyzed it as a function of the laser fluence, sample nature, and used contamination. The data show that the band gap of the sample is important for the LIC process in the first growth stage. The light absorbed in the sample leads to a temperature rise that drives the deposit growth. This knowledge opens a new pathway to minimize LIC that is complementary to studies that aim to reduce the adsorption of contaminant molecules by making chemical surface treatments.
13 September 2018 in Optical Engineering
Laser damage measurements with multiple pulses at constant fluence (S-on-1 measurements) are of high practical importance for design and validation of high-power photonic instruments. Using nanosecond lasers, it was recognized long ago that single-pulse laser damage is linked to fabrication-related defects. Models describing the laser damage probability as the probability of encounter between the high fluence region of the laser beam and the fabrication-related defects are thus widely used. Nanosecond S-on-1 tests often reveal the “fatigue effect,” i.e., a decrease of the laser damage threshold with increasing pulse number. Most authors attribute this effect to cumulative material modifications operated by the incubation pulses. We discuss the different situations that are observed upon nanosecond S-on-1 measurements that are reported in literature and speak in particular about the defects involved in the laser damage mechanism. These defects may be fabrication related or laser induced, stable or evolutive, cumulative or of short lifetime.