1 January 2011 in The Journal of the Acoustical Society of America
Phonation into a glass tube is a voice training and therapy method that leads to beneficial effects in voice production. It has not been known, however, what changes occur in the vocal tract during and after the phonation into a tube. This pilot study examined the vocal tract shape in a female subject before, during, and after phonation into a tube using computer tomography (CT). Three-dimensional finite-element models (FEMs) of the vocal tract were derived from the CT images and used to study changes in vocal tract input impedance. When phonating on vowel [a:] the data showed tightened velopharyngeal closure and enlarged cross-sectional areas of the oropharyngeal and oral cavities during and after the tube-phonation. FEM calculations revealed an increased input inertance of the vocal tract and an increased acoustic energy radiated out of the vocal tract after the tube-phonation. The results indicate that the phonation into a tube causes changes in the vocal tract which remain also when the tube is removed. These effects may help improving voice production in patients and voice professionals.
1 November 2020 in The Journal of the Acoustical Society of America
Nasal cavities are known to introduce antiresonances (dips) in the sound spectrum reducing the acoustic power of the voice. In this study, a three-dimensional (3D) finite element (FE) model of the vocal tract (VT) of one female subject was created for vowels [a:] and [i:] without and with a detailed model of nasal cavities based on CT (Computer Tomography) images. The 3D FE models were then used for analyzing the resonances, antiresonances and the acoustic pressure response spectra of the VT. The computed results were compared with the measurements of a VT model for the vowel [a:], obtained from the FE model by 3D printing. The nasality affects mainly the lowest formant frequency and decreases its peak level. The results confirm the main effect of nasalization, i.e., that sound pressure level decreases in the frequency region of the formants F1–F2 and emphasizes the frequency region of the formants F3–F5 around the singer's formant cluster. Additionally, many internal local resonances in the nasal and paranasal cavities were found in the 3D FE model. Their effect on the acoustic output was found to be minimal, but accelerometer measurements on the walls of the 3D-printed model suggested they could contribute to structure vibrations.
1 September 2021 in The Journal of the Acoustical Society of America
Classical singers use nasal consonants as “resonance exercises,” and experimental results have shown that singers may use some velopharyngeal opening (VPO), most often in [a:] and more seldom in [i:] or [u:]. In particular, male singers have been found to increase VPO as pitch rises toward register change frequencies (passaggi). Laryngoscopic findings have shown that some VPO stabilizes vocal fold vibration; the effect is related to positive reactance. This study investigates the effects of VPO on vocal tract (VT) reactance over the range of fundamental frequencies (f0) used in singing using a computerized tomography-based finite element model of the VT and nose of a female. According to the results, by raising the lowest VT resonances, the VPO increased the VT reactance in the frequency ranges 207–359 Hz for [i:], 265–411 Hz for [u:], and 500–611 Hz for [a:], depending on the VPO size (full or half VPO). These frequency ranges are close to the first and second passaggio of a female singer. The change may have an especially practical stabilizing effect for [a:], which is otherwise characterized by very large changes in VT reactance and negative reactance at the second passaggio.
28 June 2017 in Mechanics
This paper presents a model of the interaction of mating gears. The approach uses 3D gear geometry for the calculation of teeth penetration. The contact force is evaluated using the penetration between all mating teeth and the known contact stiffness. Gear meshing is evaluated using an analytical solution based on gear flank parameterization. The advantage of such an approach is to involve real gear geometry in the calculation of the contact force. The model involves the effects of the backlash between teeth (gear rattling, hammering), engagement and disengagement of the teeth pair in contact and the variation of the number of teeth pairs in contact (gear whine). The ideal tooth flank geometry is modified using the measured flank modifications. The dynamic behaviour of the interaction between two gears is modelled and compared with the 2D spring-damper model. DOI: http://dx.doi.org/10.5755/j01.mech.23.3.14325