Christina DiMarino

Christina DiMarino

Auto-generated profile, based on publicly available information

Christina DiMarino

Center for Power Electronics Systems, Virginia Tech, Arlington, VA, USA

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 February 2023 in Journal of Physics D: Applied Physics
Verified
Journal Article
Open access
PDF file
YQYuan Qin
Yuan Qin
BABenjamin Albano
Benjamin Albano
JSJoseph Spencer
Joseph Spencer
JLJames Spencer Lundh
James Spencer Lundh
BWBoyan Wang
Boyan Wang
YZYuhao Zhang
Yuhao Zhang
Power semiconductor devices are fundamental drivers for advances in power electronics, the technology for electric energy conversion. Power devices based on wide-bandgap (WBG) and ultra-wide bandgap (UWBG) semiconductors allow for a smaller chip size, lower loss and higher frequency compared with their silicon (Si) counterparts, thus enabling a higher system efficiency and smaller form factor. Amongst the challenges for the development and deployment of WBG and UWBG devices is the efficient dissipation of heat, an unavoidable by-product of the higher power density. To mitigate the performance limitations and reliability issues caused by self-heating, thermal management is required at both device and package levels. Packaging in particular is a crucial milestone for the development of any power device technology; WBG and UWBG devices have both reached this milestone recently. This paper provides a timely review of the thermal management of WBG and UWBG power devices with an emphasis on packaged devices. Additionally, emerging UWBG devices hold good promise for high-temperature applications due to their low intrinsic carrier density and increased dopant ionization at elevated temperatures. The fulfillment of this promise in system applications, in conjunction with overcoming the thermal limitations of some UWBG materials, requires new thermal management and packaging technologies. To this end, we provide perspectives on the relevant challenges, potential solutions and research opportunities, highlighting the pressing needs for device–package electrothermal co-design and high-temperature packages that can withstand the high electric fields expected in UWBG devices.

11 November 2019 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
CDChristina M. DiMarino
Christina M. DiMarino
BMBassem Mouawad
Bassem Mouawad
CJC. Mark Johnson
C. Mark Johnson
DBDushan Boroyevich
Dushan Boroyevich
RBRolando Burgos
Rolando Burgos
The advancement of silicon carbide (SiC) power devices with voltage ratings exceeding 10 kV is expected to revolutionize medium- and high-voltage systems. However, present power module packages are limiting the performance of these unique switches. The objective of this research is to push the boundaries of high-density, high-speed, 10 kV power module packaging. The proposed package addresses the well-known electromagnetic and thermal challenges, as well as the more recent and prominent electrostatic and electromagnetic interference (EMI) issues associated with high-speed, 10 kV devices. The high-speed switching and high voltage rating of these devices causes significant EMI and high electric field. Existing power module packages are unable to address these challenges, resulting in detrimental EMI and partial discharge that limit the converter operation. This paper presents the design and testing of a 10 kV SiC MOSFET power module that switches at a record 250 V/ns without compromising the signal and ground integrity due to an integrated screen reduces the common-mode current by ten times. This screen connection simultaneously increases the partial discharge inception voltage by more than 50 %. With the integrated cooling system, the power module prototype achieves a power density of 4 W/mm3.

1 March 2016
Verified
Conference Paper
Closed access
JWJun Wang
Jun Wang
ZSZhiyu Shen
Zhiyu Shen
CDChristina DiMarino
Christina DiMarino
RBRolando Burgos
Rolando Burgos
DBDushan Boroyevich
Dushan Boroyevich
This paper shows a gate driver design for 1.7 kV SiC MOSFET module as well a Rogowski-coil based current sensor for effective short circuit protection. The design begins with the power architecture selection for better common-mode noise immunity as the driver is subjected to high dv/dt due to the very high switching speed of the SiC MOSFET modules. The selection of the most appropriate gate driver IC is made to ensure the best performance and full functionalities of the driver, followed by the circuitry designs of paralleled external current booster, Soft Turn-Off, and Miller Clamp. In addition to desaturation, a high bandwidth PCB-based Rogowski current sensor is proposed to serve as a more effective method for the short circuit protection for the high-cost SiC MOSFET modules.

27 September 2019 in IEEE Journal of Emerging and Selected Topics in Power Electronics
Verified
Journal Article
Closed access
CDChristina DiMarino
Christina DiMarino
BMBassem Mouawad
Bassem Mouawad
CJC. Mark Johnson
C. Mark Johnson
MWMeiyu Wang
Meiyu Wang
YTYan-Song Tan
Yan-Song Tan
RBRolando Burgos
Rolando Burgos
Wide bandgap (WBG) power devices with voltage ratings exceeding 10 kV have the potential to revolutionize medium- and high-voltage systems due to their high-speed switching and lower ON-state losses. However, the present power module packages are limiting the performance of these unique switches. The objective of this article is to push the boundaries of high-density, high-speed, 10-kV power module packaging. The proposed package addresses the well-known electromagnetic and thermal challenges, as well as the more recent and prominent electrostatic and electromagnetic interference (EMI) issues associated with high-speed, 10-kV devices. The module achieves low and balanced parasitic inductances, resulting in a record switching speed of 250 V/ns with negligible ringing and voltage overshoot. An integrated screen reduces the common-mode (CM) current that is generated by these fast voltage transients by ten times. This screen connection simultaneously increases the partial discharge inception voltage (PDIV) by more than 50%. A compact, medium-voltage termination and system interface design is also proposed in this article. With the integrated jet-impingement cooler, the power module prototype achieves a power density of 4 W/mm 3 . This article presents the design, prototyping, and testing of this optimized package for 10-kV SiC MOSFETs.

17 September 2015 in IEEE Industrial Electronics Magazine
Verified
Journal Article
Closed access
CDChristina Marie DiMarino
Christina Marie DiMarino
RBRolando Burgos
Rolando Burgos
BDBoroyevich Dushan
Boroyevich Dushan
For several decades, silicon (Si) has been the primary semiconductor choice for power electronic devices. During this time, the development and fabrication of Si devices has been optimized, which, in combination with the large abundance of material, has resulted in high manufacturing capability and extremely low costs. However, Si is approaching its limits in power conversion [1], [2]; improved efficiency, reduced size, and lower overall system cost can now be achieved by replacing Si devices with wide-bandgap (WBG) semiconductors [1]?[3].

7 April 2017 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Closed access
MJMarko Jaksic
Marko Jaksic
ZSZhiyu Shen
Zhiyu Shen
ICIgor Cvetkovic
Igor Cvetkovic
DBDushan Boroyevich
Dushan Boroyevich
RBRolando Burgos
Rolando Burgos
FCFang Chen
Fang Chen
This paper describes the design and implementation of the first medium-voltage impedance measurement unit (IMU) capable of characterizing in situ source and load impedances of dc and ac networks (4160 V ac, 6000 V dc, 300 A, 2.2 MVA) in the frequency range of 0.1 Hz-1 kHz. The IMU comprises three power electronics building blocks (PEBBs), each built using 10-kV SiC MOSFET H-bridges. The modularity of the PEBBs allows for both series and shunt perturbation injection modes to be realized, as both injection modes are needed to accurately predict the stability of the electrical system. The effectiveness of the proposed impedance identification approach is experimentally verified on medium voltage power grid.